A GDU calculator works out growing degree units, also called growing degree days, from the highest and lowest temperature of each day and a base temperature. Enter one day, or paste a list of days, and it adds up the heat that a crop or insect has received. Growers use the total to predict when a crop will reach a stage.
How to use the GDU calculator
- Choose US or metric units, and one day or many days.
- Enter the highest and lowest temperature, or paste one high and low per line, and the base temperature.
- Choose a method and press Calculate.
The formula
The Wikipedia article on growing degree-days gives the daily value as the maximum temperature plus the minimum temperature, divided by 2, minus the base temperature.[1] Units are added up as the season goes on: the page says growing degree units are accumulated by adding each day's contribution.[1] For a day with a high of 23 °C, a low of 12 °C and a base of 10 °C, the page gives (23 + 12) ÷ 2 − 10 = 7.5.[1] The calculator gives 7.5 °C-days for the same values.
When it is cooler than the base
On cool days the average can fall below the base. The page shows two ways to handle this. In the first, the day counts as zero: max{(Tmax + Tmin) ÷ 2 − Tbase, 0}. In the second, the minimum is raised to the base before averaging.[1] It also states that any temperature below the base is set to the base before the average is calculated.[1] The page's example is a high of 13 °C and a low of 5 °C with a base of 10 °C: the first method gives 0, and the second gives (13 + 10) ÷ 2 − 10 = 1.5.[1] The calculator offers both, and shows 0 and 1.5 for this day.
The upper limit
The page says the maximum temperature is usually capped at 30 °C because most plants and insects do not grow any faster above that temperature, though some warm temperate and tropical plants do need significant heat above 30 °C.[1] It describes a modified version for corn, which starts growing at 10 °C and stops at 30 °C, so that degree-days above 30 °C do not count.[1] The page gives no explicit formula for this, so our corn option applies the cap of 30 °C and the base to both temperatures before averaging. That is our own working. For a day of 35 °C and 15 °C with a base of 10 °C it gives 12.5.
Choosing a base temperature
The page says common baselines are 5 °C for cool-season plants and 10 °C for warm-season plants and most insect development, and that the best base temperature is often determined experimentally for the life cycle of the plant or insect.[1] Its crop list gives 4.5 °C for wheat, barley, rye, oats and lettuce, 8 °C for sunflower and potato, and 10 °C for maize, sorghum, rice, soybeans and tomato.[1] For pests it lists 6 °C for the stalk borer, 7 °C for the corn rootworm, 9 °C for the alfalfa weevil and 10 °C for the black cutworm and the European corn borer.[1] The page gives bases in degrees Celsius only. Our US default of 50 °F is the Fahrenheit equivalent of 10 °C, so check the base that your own crop guide recommends.
Fahrenheit and Celsius
The page states the conversion between the two units of degree-days: Celsius degree-days equal five ninths of Fahrenheit degree-days.[1] The calculator works in Celsius internally and shows both. A day of 86 °F and 50 °F with a base of 50 °F is 30 °C and 10 °C with a base of 10 °C, which gives 10 °C-days, or 18 °F-days. These values are our own application.
Using the total
The page lists total degree-days that crops need to reach stages, using a 10 °C base in its table. Corn needs from 800 to 2,700 in different varieties to reach maturity, and dry beans need 1,100 to 1,300.[1] The page itself notes that the table uses a 10 °C base even for crops whose own base is 4.5 °C, so compare your totals with figures that use the same base and method. It also says that unless plants are stressed by other factors such as moisture, development rate depends on daily air temperature, and that degree-days are typically measured from the winter low.[1]
Many days at once
Choose many days, enter one line per day with the high first and then the low, and the calculator adds up the units. Two days of 23 and 12, and 13 and 5, with the raise method and a base of 10 °C, give 7.5 + 1.5 = 9 °C-days. Use your own station's data for the planting date to the current date.
Keeping a record
Record the daily highs and lows from the same weather station each day so that your totals are consistent. Start counting on the planting date or, for pests, on the date given in your pest guide. Add the daily units to the running total, and compare the total with the figure given for the stage that you are waiting for.
Common mistakes
- Swapping the high and the low. The high comes first.
- Using the wrong base. A crop's base is not always 10 °C.
- Mixing methods. Compare totals only when the same method was used.
What next
Use this often? Add GDU to your Home screen.
Frequently asked questions
What is a GDU calculator?
A tool that works out growing degree units, the heat gained each day above a base temperature, and adds them up over a season.
What is the GDU formula?
(Tmax + Tmin) ÷ 2 − Tbase for each day, accumulated over the season. Temperatures below the base are set to the base.
What base temperature should I use?
It depends on the crop or pest. Common baselines are 5 °C for cool-season plants and 10 °C for warm-season plants and most insects.
Why is the temperature capped at 30 °C?
Most plants and insects do not grow faster above 30 °C, so heat above that is usually not counted.
Are GDU and GDD the same?
In practice yes. Growing degree units and growing degree days both measure accumulated heat above a base.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.