A solar panel calculator estimates how big a solar system you need and how many panels that means. It starts from the electricity you use, shown in kWh or units on your bill, and the sunshine where you live. Enter those with your panel's rating, and this solar panel calculator works out the system size, the panel count and the electricity the panels should make each month and year.
How to use the solar panel calculator
- Enter your monthly use in kWh from your electricity bill. An average over a year is best, as use changes with the seasons.
- Enter the peak sun hours for your area from local solar data.
- Enter the panel rating in watts and the losses, or keep the defaults.
- Read the result: the number of panels, the system size and the expected output.
How it's calculated
Solar panels are rated under standard test conditions, with sunlight of 1,000 W per square meter and the cells at 25 °C. A peak sun hour is one hour of sunlight at that strength, so a 1 kW system in 5 peak sun hours could make up to 5 kWh in a day. Real systems make less: panels heat up in the sun, which alone typically lowers output by about 15 to 20%, and wiring, the inverter and dust take a little more. The calculator applies your loss figure, 20% by default.
- Daily energy = monthly use ÷ 30.4 days
- System size (kW) = daily energy ÷ (peak sun hours × (1 − losses))
- Panels = system size in watts ÷ panel rating, rounded up
Worked example
A home uses 300 kWh a month, which is about 9.86 kWh a day. With 5 peak sun hours and 20% losses, each kW of panels makes about 4 kWh a day, so the home needs about 9.86 ÷ 4 = 2.47 kW. With 400 W panels, that is 2,466 ÷ 400 = 6.2, rounded up to 7 panels, a 2.8 kW system that should make about 341 kWh a month, or 4,088 kWh a year.
What changes the real output
- Shade from trees, buildings or water tanks, even on part of a panel.
- Direction and tilt of the roof. Panels facing the sun for most of the day make the most.
- Season and weather. Sun hours vary through the year, so use a yearly average.
- Temperature. Panels make less when they are hot.
- Inverter size. The inverter limits the AC power the system can deliver at its peak.
To check the roof area you have, use the square footage calculator, and to compare the cost with the savings, the ROI calculator.
Worked example: a larger home with less sun
Say your bills show an average of 900 kWh a month and your area gets about 4.5 peak sun hours a day. Keep the 400 W panel rating and the 20% losses.
- Energy to cover each day: 900 ÷ 30.4 = 29.6 kWh
- Output per kW of panels: 4.5 × (1 − 0.20) = 3.6 kWh a day
- System size needed: 29.6 ÷ 3.6 = 8.22 kW
- Panels: 8,220 W ÷ 400 W = 20.6, rounded up to 21 panels, which make 8.4 kW
- Expected output: about 920 kWh a month, or 11,038 kWh a year
The same home in a place with only 3.5 peak sun hours would need 10.57 kW, or 27 panels.
Covering only part of your bill
The “Share of your use to cover” box lets you size a smaller system. Many people start with half their use because of roof space or budget. With 50% in the example above, the calculator aims at 14.8 kWh a day, so you need about 4.11 kW, or 11 panels of 400 W, making around 482 kWh a month. You can also enter more than 100%, up to 200%, if you plan to add an electric car or a heat pump and want room for the extra load.
What the loss figure includes
The losses box covers everything that stops the panels from delivering their full rating. NREL’s PVWatts model lists the losses it doesn’t model in detail: soiling, shading, snow cover, mismatch, wiring, connections, light-induced degradation, nameplate rating, system age and availability.[2] Its default values for these add up to a total of 14%.[2] The total isn’t a simple sum: each loss reduces what is left after the others.[2]
| Loss in PVWatts | Default |
|---|---|
| Soiling (dirt and dust) | 2% |
| Shading | 3% |
| Mismatch between panels | 2% |
| Wiring | 2% |
| Light-induced degradation | 1.5% |
| Availability (downtime) | 3% |
PVWatts models the inverter separately and works out the effect of panel temperature on its own, using a reference cell temperature of 25 °C.[2] This calculator has no separate step for heat or the inverter, so its default of 20% is set higher than the 14% to leave room for them. If you enter 14% for the 300 kWh home in the example above, you get 6 panels instead of 7.
Is your roof a good fit?
The U.S. Department of Energy says panels typically perform best on south-facing roofs with a slope between 15 and 40 degrees, though other roofs may be suitable too.[3] It also warns that trees creating excessive shade on the roof may make rooftop panels a poor choice.[3] It also suggests you consider the age of your roof and how long it has until it needs replacing.[3]
For an idea of size, NREL’s analyses use an average home system of 7.15 kW, within a range of 3 to 11 kW.[3]
Common mistakes with a solar panel calculator
- Using one month’s bill. A summer or winter bill can be far from your average. Add up a year of bills and divide by 12.
- Typing daylight hours as sun hours. Twelve hours of daylight is not twelve peak sun hours. Peak sun hours count only sunlight at full strength, so the figure is always much lower than the hours of daylight.
- Setting losses to zero. No real system makes its full rating every hour. Leaving losses at 0% gives too few panels.
- Treating the count as final. The panel count is a starting point for a quote. An installer checks roof space, shade, wiring and local rules before fixing the design.
Once you know the size, the solar savings calculator can help you weigh the cost against your bills, and the electricity bill calculator shows what you pay today.
What next
Use this often? Add Solar Panel to your Home screen.
Frequently asked questions
How does the solar panel calculator work out the number of panels?
It divides your daily energy use by the output of 1 kW of panels in your sun hours, after losses, then divides by the panel rating and rounds up.
What are peak sun hours?
The number of hours a day the sunlight would add up to if it were at full strength, 1,000 W per square meter, the level panels are rated at.
How many panels do I need for 300 kWh a month?
With 5 peak sun hours, 20% losses and 400 W panels, about 7 panels, a 2.8 kW system.
Why does my system make less than its rating?
Panels are rated in test conditions. In real use, heat lowers output by about 15 to 20%, and wiring, the inverter, dust and shade take more.
How many solar panels do I need for 900 kWh a month?
With 4.5 peak sun hours, 20% losses and 400 W panels, you need about 8.22 kW, which is 21 panels. They should make about 920 kWh a month. More sun means fewer panels.
What loss figure should I use?
The default of 20% suits most homes. NREL’s PVWatts uses 14% for dirt, shading, wiring and similar losses, but it models heat and the inverter separately, so a simple estimate like this one needs a higher figure.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.