Saved

Press the star next to a tool's name to save it.

All my tools

Daily Light Integral Calculator

Use this daily light integral calculator to find DLI in mol/m²/day from PPFD and hours of light, or the PPFD or light hours needed for a target DLI.

Restored your last values ·

Enter the average PPFD of your light and the hours it is on to get the daily light integral. Or enter a target DLI to see the PPFD or the hours that you need. You can also enter a list of PPFD readings taken at equal intervals through the day.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to work out, fill in the boxes, then press Calculate.

A daily light integral calculator shows how much light a plant receives in a day. Enter the average PPFD of your light in micromoles per square metre per second and the hours it is on, and it gives the daily light integral, DLI, in moles per square metre per day. It also works out the PPFD or the hours that you need for a target.

How to use the daily light integral calculator

  1. Choose DLI from PPFD and hours, or another mode.
  2. Enter the average PPFD and the hours of light, or a target DLI.
  3. Press Calculate.

What DLI is

The Wikipedia article on the daily light integral defines it as the number of photosynthetically active photons accumulated in a square metre over a day, in mol per square metre per day, and says that it is a function of light intensity and the length of the day.[1] It defines PPFD as the number of photons in the PAR range received in a square metre per second, in µmol per square metre per second.[1] The article on photosynthetically active radiation says that PAR spans 400 to 700 nanometres.[2]

The formula

For a constant PPFD, the page gives DLI = 3.6 × 10 to the power −3 × PPFD × light hours per day, where the factor comes from converting micromoles to moles and hours to seconds.[1] The other page gives the same thing as 0.0036 × PPFD × the duration of exposure.[2] The page also states that 1 µmol per square metre per second over a full day is 0.0864 mol per square metre per day.[1] For 300 µmol/m²/s over 16 hours, the DLI is 0.0036 × 300 × 16 = 17.28 mol/m²/day. The other modes rearrange the same formula to give the PPFD or the hours for a target DLI.

When the light changes

The page says that the DLI describes the sum of the per-second PPFD measurements during a 24-hour period.[1] For daylight, the light rises and falls, so a single average over the hours is only an estimate. The list mode adds up readings taken at equal intervals: each reading is multiplied by the interval in seconds and the total is divided by a million. For the nine hourly readings 0, 0, 100, 400, 800, 800, 400, 100 and 0, the total is 2,600 and the DLI is 2,600 × 3,600 ÷ 1,000,000 = 9.36. This example is our own.

Typical values

The page says that outdoors, bright summer days at some locations can exceed 70 mol/m²/day, and that monthly averages are 20 to 40 in the tropics, 15 to 60 at 30 degrees latitude and 1 to 40 at 60 degrees.[1] In the shade, the DLI can be less than 1, even in summer.[1] Greenhouses absorb or reflect 30 to 70 percent of the outside light, so their DLI rarely exceeds 30, and values from 10 to 30 are most common in growth chambers.[1]

What the number means for plants

The page says that light is particularly limiting below 5 mol/m²/day and that most traits approach saturation beyond a DLI of 20.[1] The calculator gives a comment after each result with these two limits. It also notes that horticultural plants need a minimum DLI to be marketable, though the page gives no figure.[1] The needs of individual crops differ, so use a crop guide for the target. The pages we read give no crop targets.

Lux and watts

The pages we read give no factor for converting lux, foot-candles or watts per square metre of sunlight into PPFD, and the PAR page says that illuminance is based on human perception of brightness.[2] The calculator therefore takes PPFD directly, as read from a quantum sensor or a lamp's data sheet. A lamp's PPFD depends on its distance from the plants, so measure at the leaf level.

Planning a grow light schedule

To reach a DLI of 12 with a lamp that gives 200 µmol/m²/s at the plants, you need 12 ÷ (0.0036 × 200) = 16.7 hours of light. If that is too long, increase the intensity: 12 hours at 278 µmol/m²/s gives the same DLI. These examples are our own calculations. A very long photoperiod may not suit every plant, so check the guidance for your species.

Reading a light meter

A quantum sensor reports PPFD in micromoles per square metre per second. Take readings at the height of the leaves, at several spots under the lamp or across the bench, because the light is brighter in the middle than at the edges. Average the readings to get a figure for the whole area. For daylight, take a reading every hour or half hour, and use the list mode. A cloudy day can give a DLI that is a fraction of a sunny day's, which is why the page notes that the outdoor value depends on latitude, the time of year and the cloud cover.{1}

Adjusting light for a crop

If a crop needs a higher DLI than your light provides, you can extend the photoperiod, raise the PPFD by moving the lamp closer or adding lamps, or both. Raising the intensity costs more power, while extending the hours costs more time under the lamp. The calculator lets you compare the two choices, because it shows the PPFD needed for a fixed number of hours and the hours needed for a fixed PPFD.

Common mistakes

  • Using the peak PPFD. Use the average over the hours of light.
  • Mixing up units. PPFD is in micromoles, DLI in moles.
  • Measuring at the lamp. Measure where the leaves are.

What next

Use this often? Add Daily Light to your Home screen.

Frequently asked questions

What is a daily light integral calculator?

A tool that finds the total photosynthetic light a plant receives in a day, in mol per square metre per day, from PPFD and the hours of light.

What is the DLI formula?

DLI = 0.0036 × PPFD × hours of light per day, with PPFD in µmol/m²/s.

What is a good DLI?

It depends on the plant. The page says light is limiting below 5 mol/m²/day and most traits approach saturation beyond 20.

How do I calculate DLI for changing light?

Add up readings taken at equal intervals, multiply each by the interval in seconds and divide the total by 1,000,000.

What is the DLI of 1 µmol/m²/s for 24 hours?

0.0864 mol/m²/day.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools