A cut list optimizer tells you how many boards to buy and where to saw each one. Enter the length of the stock board, the width of your saw cut, and the list of pieces you need. The optimizer lays the pieces out on as few boards as it can, shows a diagram of every board and tells you how much is left over.
Woodworkers, deck builders, framers and metal fabricators all face the same puzzle with pipe, trim, bar stock and lumber: a pile of lengths to cut from standard sizes. A good plan saves money on stock and saves a trip back to the store.
How to use the cut list optimizer
- Pick your unit: inches, millimetres or centimetres.
- Enter the length of the stock board, for example 96 inches for an 8-foot board.
- Enter the kerf, the width of the saw cut. Leave it blank if you want to ignore it.
- List the pieces, one line per size, as length, an x and the quantity. A line with only a length means one piece. Fractions such as 23 1/2 are fine.
- Optionally enter how many boards you already have. Press Calculate.
What kerf is and why it matters
The kerf is the narrow channel the saw leaves behind, and by extension the measure of its width [3]. It is material turned to sawdust, so it cannot be part of any piece. One example gives a kerf of 1/8 inch, or 3 millimetres, which reduces the number of pieces you can cut from an 8-foot board [3]. The optimizer counts one kerf between each two neighbouring pieces on a board. Two 48-inch pieces do not fit on a 96-inch board with a 1/8-inch kerf, because 48 + 1/8 + 48 is 96 1/8 inches.
How the plan is worked out
Finding the best possible layout is a known hard problem. The one-dimensional cutting stock problem, cutting standard-sized pieces of stock to meet an order with the least waste, is NP-hard and reducible to the knapsack problem [1]. For a few dozen pieces on a workshop bench you do not need a perfect proof. This tool uses a classic quick method, first-fit decreasing. It sorts the pieces from longest to shortest, then puts each piece on the first board that still has room, starting a new board only when none does [2].
First-fit decreasing is a heuristic. It is fast and usually close to the best answer, but sorting by size still does not guarantee an optimal solution [2]. Its worst case is known: it never needs more than 11/9 of the optimal number of boards plus 6/9 of a board [2]. So a layout from this page is a very good starting plan, not a proof that no cleverer arrangement exists. If the result is one board above the lower bound, try changing a length slightly or splitting a long piece to see if the plan improves.
The lower bound shown with the result
To help you judge the plan, the tool also reports a simple lower bound: the total length of all pieces divided by the stock length, rounded up. This is the same idea as the usual lower bound for the problem, the total product divided by the master roll size [1]. No layout can use fewer boards than that. When the number of boards in the plan equals the lower bound, the plan is certainly the minimum. When it is one more, the plan may still be best because kerf and awkward lengths can force an extra board.
Reading the diagram and the tables
- Coloured blocks are pieces. Pieces of the same length share a colour, and the length is printed inside when it fits.
- Dark lines are the kerf between neighbouring pieces.
- Dashed boxes are the offcut, the part of the board left unused at the end.
- Board table: each board with its cuts in the order to cut them, and the offcut length.
- Facts table: the number of boards, pieces, total cut length, total kerf, offcut and waste percentage.
Worked example
Say you need four 48-inch pieces and two 24-inch pieces from 96-inch boards with a 1/8-inch kerf. Because two 48s need 96 1/8 inches, each 48 gets its own board. A 24-inch piece fits next to a 48 in 72 1/8 inches, but a second 24 would need 96 1/4, so the other 24 goes on the next board. The result is four boards, with two offcuts of 23 7/8 inches and two of 48 inches. The lower bound is 3, so the plan is one board above it, and the diagram shows why: the kerf is the difference.
Tips for a better cut list
- Measure the real stock. A board sold as 8 feet is often slightly longer or shorter.
- Add a little to each piece if the ends will be trimmed square.
- Cut the long pieces first and keep every offcut in a labelled bin.
- Mind wood grain, knots and defects, which this tool does not know about.
- If you need pieces from more than one stock length, run the tool once for each length.
What next
Use this often? Add Cut List Opt to your Home screen.
Frequently asked questions
What does a cut list optimizer do?
It plans how to cut a list of pieces from stock boards of one length so you buy as few boards as possible, and it shows each board with its cuts and offcut.
Is the result always the minimum number of boards?
Not always. The tool uses first-fit decreasing, a fast heuristic that is close to optimal but not guaranteed. It shows a lower bound so you can see whether the plan reaches the theoretical minimum.
How is kerf handled?
One kerf is counted between each two neighbouring pieces on a board. Leave the box blank to ignore the saw cut. Cutting off the last piece does not need an extra kerf in this model.
What do I type for fractions and units?
Write mixed numbers like 23 1/2 or decimals like 23.5. Choose inches, millimetres or centimetres once and use that unit for the stock, the kerf and every piece.
Can I plan pieces from two different board lengths?
Not in one run. Run the tool once for each stock length and split the pieces between them, putting the longest pieces on the longest boards.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.