This framing calculator works out how many studs and how much plate lumber you need to frame a wood stud wall. Enter the wall length, choose the stud spacing, add any extra studs for corners and openings, and the framing calculator gives the number of studs, the length of plate material for a sole plate and double top plate, and the number of plate boards to buy.
How to use the framing calculator
- Choose US or metric units. US (feet and inches) is the default.
- Enter the wall length and choose the stud spacing: 12, 16 or 24 inches on center.
- Add extra studs for corners, intersecting walls and openings.
- Enter a plate board length and waste allowance if you like, then press Calculate.
Stud spacing
Wall studs are set at a regular spacing measured from the center of one stud to the center of the next, called on center. The 2021 International Residential Code (IRC) tables for wood wall studs, such as Table R602.3(6), list studs at 12, 16 and 24 inches on center. The right spacing and stud size depend on the wall height, what the wall supports and the design wind speed, so check your plans or local code.
Top and bottom plates
Studs sit on a bottom plate, also called a sole plate, and are capped by a top plate. IRC section R602.3.2 says wood stud walls must be capped with a double top plate, overlapping at corners and intersections with bearing partitions, with end joints offset by at least 24 inches. With the sole plate, that's three plates along the length of the wall, which is what the calculator assumes. The code allows a single top plate only in specific cases with extra ties.
How the calculator works
The calculator divides the wall length by the stud spacing, rounds up and adds one, so there's a stud at each end of the wall. It then adds the extra studs you entered and the waste allowance. For plates, it multiplies the wall length by three and, if you give a board length, works out how many boards you need, including waste.
Worked example
A 20-foot wall is 240 inches long. At 16 inches on center, 240 ÷ 16 = 15, plus one, so you need 16 studs. At 24 inches on center, the same wall needs 11 studs. Either way, the plates total 3 × 20 = 60 feet, or four 16-foot boards. With a 10% waste allowance, the 16-inch wall needs 18 studs and five 16-foot plate boards.
Extra studs
A plain wall only needs the regular studs, but corners, wall intersections and openings need more. Each opening usually has king studs beside the jack studs that hold the header, and short cripple studs above the header and below a window sill. Add these up from your plan and enter them as extra studs. The door header size calculator can help with the jack studs for a header.
Reading the results
The big number is the total number of studs, including extras and waste. The table shows the studs before waste, the total plate length, the number of plate boards (if you entered a board length) and the stud spacing.
Choosing 16 or 24 inches
Studs at 16 inches on center are common for many walls, while 24-inch spacing uses fewer studs and leaves more room for insulation, but it depends on the wall's height, loads and wind exposure. The IRC tables show, for example, that at 16 inches on center an 11-foot wall carrying only a roof can use 2 × 4 studs, while one also carrying a floor needs 2 × 6 studs. Sheathing and drywall also need their edges to land on studs, which 16 and 24 inches both allow with standard 4 × 8-foot sheets.
Metric walls
Choose metric to enter the wall length in meters and plate board lengths in meters. The stud spacings stay at 12, 16 or 24 inches, shown in millimeters as 305, 406 and 610 mm, since those are the spacings in the IRC tables. Plate length is shown in meters.
Ordering lumber
Studs come in standard lengths cut for common wall heights, so order studs to suit your wall height and plates in the longest lengths you can handle, which means fewer joints. Keep top plate joints at least 24 inches from the joints in the plate below, as the IRC requires.
Partition walls
Interior walls that don't carry any load are framed the same way, with studs at a regular spacing and plates at the top and bottom. Run the calculator for each wall in your plan and add the results, then add the extra studs where walls meet so there's something to fix the drywall to in each corner.
Common mistakes
- Forgetting the end stud. A wall needs one more stud than spaces.
- Counting only one top plate. The IRC calls for a double top plate.
- Skipping openings. Add king, jack and cripple studs.
- No allowance for waste. Some studs will be warped or cut wrong.
Tips
- Lay out stud centers from one end so sheathing edges land on studs.
- Stagger top plate joints at least 24 inches.
- Pick straight studs for corners and openings.
What next
Use this often? Add Framing to your Home screen.
Frequently asked questions
How does a framing calculator work?
It divides the wall length by the stud spacing, adds one stud for the end, adds your extra studs and works out three plates along the wall.
How many studs for a 20-foot wall?
16 studs at 16 inches on center, or 11 at 24 inches, before extras and waste.
How many top plates does a wall need?
The IRC requires a double top plate on wood stud walls, plus the sole plate at the bottom.
What stud spacing should I use?
IRC tables list 12, 16 and 24 inches on center; the right one depends on wall height, loads and wind speed.
Do I need extra studs for windows and doors?
Yes. Add king, jack and cripple studs around each opening.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.