Saved

Press the star next to a tool's name to save it.

All my tools

Turbo Airflow Calculator

Use this turbo airflow calculator to find the airflow in lb/min that an engine needs for a horsepower target, and the compressor pressure ratio from the boost.

Restored your last values ·

Choose US or metric units. Enter the horsepower you want at the crankshaft, the air/fuel ratio and BSFC for your engine, the boost and the atmospheric pressure. You get the mass flow of air the engine needs and the compressor pressure ratio.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the horsepower, air/fuel ratio, BSFC, boost and atmospheric pressure, then press Calculate.

See full result

A turbo airflow calculator finds the mass of air that an engine needs to make a target horsepower, and the pressure ratio that the compressor must give. Enter the horsepower, the air/fuel ratio, the fuel consumption and the boost. It does not pick a turbo size, but it gives the two numbers that you read on a compressor map.

How to use the turbo airflow calculator

  1. Choose US or metric units.
  2. Enter the horsepower, the air/fuel ratio and the BSFC.
  3. Enter the boost, the atmospheric pressure and, if you know it, the inlet depression.
  4. Press Calculate to see the airflow and the pressure ratio.

What this tool does, and what it does not

Choosing a turbo starts with two numbers: how much air the engine will use, and how hard the compressor must squeeze it. This page works out both from the formulas in a turbo maker's guide [1]. It does not name an inducer diameter or a model. The guide that we used points the reader to a separate product tool for that step [1], and picking a turbo from the numbers needs a compressor map, which a simple page cannot read.

The airflow formula

The maker gives the airflow in pounds of air per minute as Wa = HP × A/F × BSFC ÷ 60 [1]. HP is the crankshaft horsepower, A/F is the ratio of the mass of air to the mass of fuel, and BSFC is the fuel the engine burns for each horsepower in each hour, in pounds. Multiplying the three gives pounds of air per hour, and dividing by 60 gives pounds per minute. The page uses this formula as published.

A worked example

The maker's own example is 650 horsepower, an air/fuel ratio of 11.5 and a BSFC of 0.46. The product 650 × 11.5 × 0.46 is 3,438.5 pounds an hour, and dividing by 60 gives 57.3 pounds a minute [1]. Type those three numbers into the calculator and you get 57.31 pounds a minute, or 25.99 kilograms a minute. The kilogram figure is our own conversion, at 0.45359237 kilograms to the pound.

The pressure ratio

The compressor pressure ratio is the outlet pressure divided by the inlet pressure, PR = P2c ÷ P1c [1]. The outlet is the boost plus the atmospheric pressure, and the inlet is the atmospheric pressure less any depression in the intake before the compressor. With 12 psi of boost, 14.7 psia of atmosphere and a depression of 1 psi, the ratio is 26.7 ÷ 13.7, or 1.95 [1]. Leave the depression blank if you do not know it.

Air/fuel ratio and BSFC

The guide gives 14.7 as the air/fuel ratio for a gasoline engine with exactly enough air to burn all the fuel, and a BSFC for a gasoline turbo engine of about 0.50 to 0.60 [1]. A richer mixture has a lower ratio, so the 11.5 of the example is rich. Your engine may differ, so use figures for your fuel and tune. Lower values of the ratio or BSFC give a smaller airflow, so check which one you are changing.

Using metric units

If you choose metric, the page takes kilowatts, grams of fuel per kilowatt hour and kilopascals, and converts them to the pound units of the formula before it works. One horsepower is 0.745699872 kilowatts, one kilowatt hour is 1.3410220896 horsepower hours, and one psi is 6.894757 kilopascals. These conversions are our own working, and they change nothing in the logic. The airflow is shown in both pounds and kilograms a minute.

The horsepower per pound check

The result also divides the horsepower by the airflow, for the example 650 ÷ 57.31, or 11.34 horsepower for each pound of air a minute. This is a rough figure of our own, not a rule from the guide. You can compare it with the horsepower that the maker rates for a compressor, but the rating depends on the pressure ratio and the efficiency, so treat the comparison as a prompt for more research and not as an answer.

Why the page cannot give a turbo size

Some sites ask for an engine size and a power target and then give a single inducer diameter. We found no published formula that turns those two inputs into a compressor size, and the same inducer can suit engines of different sizes and powers, so we do not label any output a size. The maker's guide points to a compressor map and its efficiency islands for that step [1]. Use a compressor map.

What the numbers leave out

The airflow assumes the engine runs at the horsepower, ratio and BSFC that you enter. Real engines change with air temperature, altitude, intercooler losses, exhaust back pressure and volumetric efficiency. If you know the pressure lost between the compressor and the manifold, add it to the boost, as the compressor must overcome it. These notes are our own working. Use the result to start a conversation with a turbo supplier, not to buy parts.

Reading the result with a compressor map

A compressor map plots the pressure ratio against the airflow, and shows the efficiency of the compressor in islands. To use this page with one, find your airflow on the horizontal axis and your pressure ratio on the vertical axis, and see whether the point falls inside a good efficiency island, away from the surge line on the left and the choke line on the right. The map comes from the turbo maker, which is why we do not try to pick a size here. Compare more than one turbo and more than one engine speed.

Common mistakes

  • Using absolute boost. Enter the gauge boost, as the page adds the atmosphere.
  • Forgetting the units of BSFC. The formula expects pounds per horsepower per hour.
  • Reading airflow as turbo size. A size needs a compressor map.
  • Mixing horsepower at the wheels with the crank. Use crank horsepower.

What next

Use this often? Add Turbo Airflo to your Home screen.

Frequently asked questions

What is a turbo airflow calculator?

A tool that finds the air an engine needs, in pounds a minute, for a power target, and the pressure ratio of the compressor.

How is the airflow worked out?

Wa = HP × A/F × BSFC ÷ 60, in pounds of air a minute.

What is the pressure ratio?

The compressor outlet pressure, boost plus atmospheric, divided by the inlet pressure.

Does this calculator choose a turbo size?

No. A size needs a compressor map and expert advice.

What BSFC should I use?

The maker's guide gives about 0.50 to 0.60 for a gasoline turbo engine, and your engine may differ.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools