This true position calculator checks whether a hole or other feature is within its GD&T position tolerance. Enter the feature's true position from the drawing, its measured X and Y coordinates and the position tolerance, and the true position calculator works out the diametric position deviation and tells you whether the feature passes, with the margin left over.
How to use the true position calculator
- Choose inches or millimeters.
- Enter the nominal X and Y, the basic dimensions to the feature's true position.
- Enter the measured X and Y from your inspection.
- Enter the position tolerance, and any bonus tolerance, then press Calculate.
What is true position?
GD&T Basics explains that the position tolerance is the total permitted variation a feature can have from its true position. The true position is the exact location defined by basic dimensions on the drawing. The position tolerance, shown in a feature control frame, is how far the feature's location may vary from that true position. For holes and pins, the tolerance zone is usually a cylinder, so the tolerance is given as a diameter. People often call the whole idea true position, although strictly the symbol is position.
The true position formula
Measuring a feature gives its deviation in X and Y from the true position. GD&T Basics shows how to convert those into a total diametric deviation:
position deviation (diameter) = 2 × √(ΔX² + ΔY²)
The square root gives the straight-line distance from the true position to the measured center, and doubling it turns that radius into a diameter, so it can be compared directly with the diameter tolerance zone. If the diametric deviation is no more than the tolerance, the feature passes.
Worked example
GD&T Basics gives this example: a hole measured .003 inch off in X and .002 inch off in Y. The diametric deviation is 2 × √(.003² + .002²) = 2 × .0036 = .0072 inch, which rounds to .007. The position tolerance is .008, so the part is within specification and passes, with about .0008 inch to spare.
Bonus tolerance
GD&T Basics describes how, when position is specified at maximum material condition (MMC), the location tolerance depends on the feature's size. As a hole gets closer to its MMC, the smallest allowed size, it must be closer to its true position; if the hole is larger but still in specification, it may stray further and still let a bolt pass through. That extra allowance is bonus tolerance. If your drawing uses MMC, work out the bonus from the feature's measured size and enter it; the calculator adds it to the stated tolerance.
Reading the results
The big number is the diametric position deviation. The line below says whether it's within the allowed tolerance. The table shows the X and Y deviations, the straight-line distance from true position, the allowed tolerance including any bonus, and the margin left: a negative margin means the feature is out of tolerance by that amount.
Why the diameter matters
A common mistake is to compare the X and Y deviations directly with the tolerance, or to compare the radial distance with the diameter tolerance. A hole .004 off in X and .004 off in Y is about .0057 from true position, which is a diametric deviation of .0113, well over a .008 tolerance, even though each deviation alone looks small. The calculator always compares the diameter with the diameter.
Checking several holes
For a bolt pattern or a plate with many holes, run the calculator for each hole using its own basic dimensions and measured location. Each hole is checked against its own tolerance zone, so one hole can pass while another fails. Recording the deviation and margin for each hole shows whether a problem is random or whether the whole pattern is shifted in one direction, which often points to a setup or datum issue rather than a single bad hole.
Metric drawings
Choose millimeters to work in metric. The formula is the same: a hole 0.05 mm off in X and 0.03 mm off in Y has a diametric deviation of 2 × √(0.05² + 0.03²) = about 0.117 mm, which passes a 0.12 mm position tolerance with very little to spare.
Position versus coordinate tolerances
Older drawings sometimes give plus-or-minus tolerances on X and Y, which form a square tolerance zone. A position tolerance forms a round zone instead. A round zone that just contains the square reaches the corners, so a position tolerance allows more variation diagonally than the same plus-or-minus limits would, while still controlling the true distance from the intended location. That's one reason GD&T position tolerances are widely used for holes that must line up with mating parts.
Common mistakes
- Forgetting to double. The zone is a diameter, so double the radial distance.
- Comparing X and Y separately. Combine them first.
- Using toleranced dimensions as nominal. Use the basic dimensions.
- Adding bonus without MMC. Bonus only applies when the frame calls for it.
Tips
- Measure from the datums named in the feature control frame.
- Check deep holes at more than one depth.
- Record the deviation and the margin for each feature.
What next
Use this often? Add True Positio to your Home screen.
Frequently asked questions
How does a true position calculator work?
It works out the diametric deviation 2 × √(ΔX² + ΔY²) and compares it with the position tolerance.
What is the formula for true position?
Position deviation (diameter) = 2 × √(X deviation² + Y deviation²).
Does .003 in X and .002 in Y pass a .008 position tolerance?
Yes. The diametric deviation is about .0072, within .008.
Why is the deviation doubled?
Because the tolerance zone is a diameter, and the square root gives a radius.
What is bonus tolerance?
Extra position tolerance allowed when position is specified at MMC and the feature departs from its MMC size.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.