This clearance hole calculator gives the right drill size for a hole that a screw or bolt passes through freely. Choose inch or metric, pick the screw size and a close, normal or loose fit, and the clearance hole calculator shows the drill to use, the allowed hole diameter range, and the drills for all three fits.
How to use the clearance hole calculator
- Choose inch or metric screw sizes.
- Pick the screw or bolt size, such as #10, 1/4 inch or M6.
- Choose the fit: close, normal or loose.
- Press Calculate.
What is a clearance hole?
A clearance hole is a hole that a fastener's shank passes through without touching the threads, so the screw only grips the part it threads into or the nut on the other side. It needs to be slightly bigger than the screw's nominal diameter. Too tight, and the screw binds or won't line up; too loose, and the parts can shift and the head has less surface to bear on.
Fit classes
The ASME B18.2.8 standard, listed by AmesWeb, gives three classes of clearance:
- Close: the least clearance, for accurate location and alignment.
- Normal: for general-purpose assembly.
- Loose: extra clearance for faster assembly, coatings, misalignment or field work.
AmesWeb notes that thread pitch doesn't change the clearance hole size: a 1/4-20 and a 1/4-28 bolt use the same hole, because it's based on the nominal diameter.
Common inch sizes
| Size | Close | Normal | Loose |
|---|---|---|---|
| #8 | #15 | #9 | #3 |
| #10 | #5 | #2 | B |
| 1/4 in | 17/64 | 9/32 | 19/64 |
| 5/16 in | 21/64 | 11/32 | 23/64 |
| 3/8 in | 25/64 | 13/32 | 27/64 |
| 1/2 in | 17/32 | 9/16 | 39/64 |
Common metric sizes
| Size | Close | Normal | Loose |
|---|---|---|---|
| M3 | 3.2 mm | 3.4 mm | 3.6 mm |
| M4 | 4.3 mm | 4.5 mm | 4.8 mm |
| M5 | 5.3 mm | 5.5 mm | 5.8 mm |
| M6 | 6.4 mm | 6.6 mm | 7 mm |
| M8 | 8.4 mm | 9 mm | 10 mm |
| M10 | 10.5 mm | 11 mm | 12 mm |
| M12 | 13 mm | 13.5 mm | 14.5 mm |
Worked example
For a 1/4-inch bolt with a normal fit, drill a 9/32-inch hole; the finished hole should measure 0.281 to 0.290 inches. For a close fit, use 17/64 (0.266 to 0.272 inches), and for a loose fit, 19/64 (0.297 to 0.311 inches). For an M6 screw with a close fit, drill 6.4 mm, with a maximum hole diameter of 6.55 mm.
Reading the results
The big number is the drill size for your screw and fit: a fraction, number or letter drill for inch sizes, or a size in millimeters for metric. The table shows the hole diameter range allowed for that fit and the drills for all three fits, so you can compare them.
Number and letter drills
Inch drill sizes come in fractions, numbers and letters. Number drills (#1 to #80) get smaller as the number rises, and letter drills (A to Z) cover sizes between the numbers and fractions. The calculator shows whichever drill the chart lists, such as #9 for a normal-fit #8 screw or B for a loose-fit #10.
Choosing a fit
Choose a close fit when two parts must line up accurately, for example when screws also locate a part, or when there are only a few fasteners. Choose a normal fit for most general assembly, where a little play makes assembly easier without letting the parts shift noticeably. Choose a loose fit when holes in two parts may not line up perfectly, such as in large assemblies or on site, or when coatings like paint or galvanizing will build up inside the hole.
Hole diameter range
The standard gives a minimum and maximum diameter for each fit, because a drilled hole is rarely exactly the drill's size. A sharp drill in a rigid setup cuts close to its size, while a worn drill or a hand-held drill can cut oversize. If you check the hole with calipers or a gauge pin, it should fall within the range shown in the table.
Inch and metric screws
Make sure you choose the right system. A 1/4-inch screw is 6.35 mm across, slightly larger than an M6 screw, so a 6.4 mm close-fit hole for M6 would be too tight for a 1/4-inch bolt. If you're not sure what screw you have, measure its outside diameter and compare it with both lists before drilling.
Small screw sizes
Small inch screws are sized by number, from #0 to #10, rather than fractions. The chart includes them, from #0 (a close-fit hole of 0.067 to 0.071 inches) up to #10, and then fractional sizes from 1/4 inch to 1½ inches.
Drilling tips
For accurate holes, center-punch or spot-drill first so the drill doesn't wander, and use a sharp drill at a suitable speed for the material. For larger holes, drilling a smaller pilot hole first helps keep the final hole round and on position. After drilling, remove the burr on both sides so the screw head and nut sit flat against the part.
Common mistakes
- Using the tap drill. A tap drill is smaller, for cutting threads; a clearance hole is bigger.
- Choosing by thread pitch. Only the nominal size matters.
- Too loose for alignment. Use close fit for dowel-like location.
- Forgetting coatings. Painted or plated parts may need a loose fit.
Tips
- Check the drilled hole with calipers against the range shown.
- Use a normal fit when you're unsure.
- Deburr the hole so the head sits flat.
What next
Use this often? Add Clearance Ho to your Home screen.
Frequently asked questions
How does a clearance hole calculator work?
It looks up the ASME B18.2.8 clearance hole chart for your screw size and fit class.
What size clearance hole for a 1/4 bolt?
9/32 inch for a normal fit, 17/64 for close and 19/64 for loose.
What size clearance hole for M6?
6.6 mm for a normal fit, 6.4 mm for close and 7 mm for loose.
What is the difference between close, normal and loose fit?
Close gives the least clearance for accurate alignment, normal is general purpose and loose allows for coatings or misalignment.
Does thread pitch change the clearance hole?
No. The hole depends on the screw's nominal diameter.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.