This bolt circle calculator works out where to drill holes spaced evenly around a circle, such as the bolt pattern on a wheel, flange or pipe fitting. Enter the bolt circle diameter, the number of holes and the angle of the first hole, and the bolt circle calculator gives the X and Y coordinates of every hole and the straight distance between neighboring holes.
How to use the bolt circle calculator
- Choose inches or millimeters.
- Enter the bolt circle diameter, the diameter of the circle through the centers of the holes.
- Enter the number of holes and, if you like, the angle of the first hole.
- Press Calculate.
What is a bolt circle?
A bolt circle, also called a pitch circle diameter or bolt pattern, is an imaginary circle through the centers of a ring of evenly spaced holes. Wheels, pipe flanges, sprockets and many machine parts use bolt circles. To lay one out, you need the position of each hole relative to the center, which is what this calculator gives.
The formulas
With n holes, each hole is 360° ÷ n further around the circle than the last. If the first hole is at angle a, the k-th hole (counting from 0) is at a + 360° × k ÷ n. With the circle's radius r (half the diameter), each hole's position is:
X = r × cos(angle)
Y = r × sin(angle)
The straight-line distance between two neighboring holes is a chord of the circle. The Wikipedia article on chords gives a chord's length as 2r × sin(θ ÷ 2), where θ is the angle between the two points. For holes 360° ÷ n apart, that becomes D × sin(180° ÷ n), where D is the bolt circle diameter.
Worked example
Take a 5-hole pattern on a 4.5-inch bolt circle, with the first hole at 0°. The holes are 72° apart. The first hole is at X = 2.25, Y = 0; the second at 72° is at X = 0.6953, Y = 2.1399; and so on around the circle. The distance between neighboring holes is 4.5 × sin 36° = 2.6450 inches, which is handy for checking your layout with calipers.
For a 6-hole pattern on a 100 mm circle, the holes are 60° apart and exactly 50 mm apart in a straight line, the same as the circle's radius.
Reading the results
The big number is the straight distance between neighboring holes. The table shows the angle between holes and each hole's angle and X and Y coordinates from the center of the circle. Negative values mean left of or below the center.
Using the coordinates
On a milling machine or drill press with a digital readout, set the center of the bolt circle as zero, then move to each X and Y coordinate in turn. To lay out by hand, draw the circle with dividers and step around it with the hole spacing, or mark each hole from the center with a protractor at the angles shown. Starting the first hole at 90° puts it at the top, which many drawings use.
Checking a pattern with calipers
The spacing between neighboring holes is the quickest way to check a drilled pattern. Measure from the edge of one hole to the matching edge of the next, which equals the center-to-center distance when the holes are the same size. Across the circle, holes directly opposite each other, which exist when the number of holes is even, are exactly one bolt circle diameter apart.
Odd and even numbers of holes
With an even number of holes, every hole has a partner directly across the circle, so you can check the diameter by measuring between opposite holes. With an odd number, such as 5, there's no hole straight across, so measuring the bolt circle is harder: that's when the hole-to-hole spacing from this calculator is especially useful. For a 5-hole pattern, the distance between two holes that skip one is D × sin(144°/2) = D × sin 72°, about 0.951 × D.
Start angle
The start angle rotates the whole pattern. At 0°, the first hole sits on the X axis to the right of center; at 90°, it sits straight above. For a 4-hole square pattern, a 45° start places the holes in the corners, so they line up diagonally with the edges of a square plate.
Inches or millimeters
Choose the unit that matches your drawing. The calculator shows four decimal places for inches and two for millimeters, which is enough for most machine shop layouts. Enter the diameter in the same unit, and every coordinate and spacing comes out in that unit too, so there's no conversion to get wrong at the machine.
Common mistakes
- Using the radius as the diameter. The bolt circle diameter is twice the radius.
- Measuring between hole edges. The bolt circle runs through the hole centers.
- Mixing axis directions. Check which way your machine's X and Y increase.
- Rounding too early. Keep all the decimal places until the final setup.
Tips
- Check the spacing between neighboring holes after drilling the first two.
- Use a start angle so a hole lines up with a feature on the part.
- Center-punch each hole before drilling.
What next
Use this often? Add Bolt Circle to your Home screen.
Frequently asked questions
How does a bolt circle calculator work?
It spaces holes 360° ÷ n apart and works out each one's X and Y as r × cos and r × sin of its angle.
How do I find the distance between bolt holes?
Use D × sin(180° ÷ n). For 5 holes on a 4.5-inch circle, that's 2.645 inches.
What is a bolt circle diameter?
The diameter of the circle through the centers of the holes, also called the pitch circle diameter.
How far apart are 6 holes on a 100 mm circle?
Exactly 50 mm, the same as the radius.
Where is the first hole?
At the start angle you choose; 0° points along the X axis and 90° straight up.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.