This bolt torque calculator works out how much torque to apply to a bolt to reach a target clamping force, or the clamping force a given torque produces. Enter the bolt diameter, the target preload (or the torque) and the nut factor, and the bolt torque calculator uses the standard torque–preload relationship to give the result in lb-ft, lb-in or N·m.
How to use the bolt torque calculator
- Choose US or metric units. US (inches, pound-force and pound-feet) is the default.
- Choose what to work out: torque from preload, or preload from torque.
- Enter the bolt diameter and, if you know it, the nut factor K. Leave K blank to use 0.20.
- Enter the target preload or the torque, then press Calculate.
The torque formula
When you tighten a bolt, it stretches slightly and clamps the parts together. That clamping force is called the preload. The Wikipedia article on bolted joints describes the relationship between the torque and the preload it produces:
T = K × D × F
Here T is the tightening torque, K is the nut factor (also called the torque coefficient), D is the bolt's nominal diameter and F is the preload. To find the preload from a torque, the calculator turns the formula around: F = T ÷ (K × D).
The nut factor
The nut factor accounts for friction in the threads and under the head or nut. Wikipedia explains that with a friction coefficient of 0.15 in both places, which is typical for steel, the nut factor works out to about 0.20, so torque ≈ 0.20 × D × F. It gives a test example: half-inch (1/2-20 UNF) bolts tightened to 800 lb-in produced an average preload of 7,700 lbf, a nut factor of 0.208. Lubrication lowers friction, and the article notes it can reduce the torque needed by 15% to 25%, which is why a fastener's torque specification says whether it's for dry or lubricated threads.
Where the torque goes
Most of the effort of tightening is lost to friction. Wikipedia notes that about 50% of the torque goes into friction under the head or nut, about 40% into friction in the threads, and only about 10% into stretching the bolt to create preload. That's why small changes in friction make a big difference to preload, and why torque wrenches on unlubricated bolts control preload to only about ±35%.
Worked example
Take a ½-inch bolt with a target preload of 7,700 lbf and the test's nut factor of 0.208. The torque is 0.208 × 0.5 × 7,700 = 800.8 lb-in, about 66.7 lb-ft, matching the test. With the standard K of 0.20, the torque would be 770 lb-in, or about 64.2 lb-ft.
In metric, a 10 mm bolt with a target preload of 20 kN and K = 0.20 needs 0.20 × 0.010 m × 20,000 N = 40 N·m.
Choosing a preload
The target preload depends on the bolt's strength and the job. Wikipedia notes that for higher-strength fasteners, the preload is usually at least 75% of the bolt's proof load, and up to 90% for permanent fasteners. The proof load depends on the bolt's grade and size, so check the bolt maker's data. If you have a torque value from a specification, choose Preload from torque to see roughly what clamping force it gives.
Reading the results
The big number is the torque (or preload) in your chosen units. The table shows the same result in other units and the nut factor used.
Accuracy of torque tightening
Because friction varies from bolt to bolt, the same torque can give quite different preloads. The Wikipedia article lists typical accuracy for different tightening methods: a torque wrench on unlubricated bolts controls preload to about ±35%, on lubricated bolts to about ±25%, and preload-indicating washers to about ±10%, while measuring the bolt's stretch directly is accurate to about ±5%. For critical joints, those more accurate methods are used instead of torque alone.
Units and conversions
Torque is often given in pound-feet in the US and newton-meters elsewhere. One pound-foot is about 1.356 newton-meters, and one pound-foot is 12 pound-inches. Preload is a force, given in pound-force (lbf) or kilonewtons (kN); one kilonewton is about 225 lbf. The calculator converts between them so you can enter values in the units you have and read the result in the units your torque wrench uses.
When to use the reverse calculation
Sometimes you're given a torque value and want to know what it does. Choose Preload from torque, enter the bolt diameter, the torque and the nut factor, and the calculator estimates the clamping force. This helps you see how much a change of lubricant or a different torque value would change the clamping force in a joint.
Common mistakes
- Using a dry torque on lubricated threads. Lubricated threads need less torque for the same preload.
- Mixing pound-feet and pound-inches. There are 12 lb-in in 1 lb-ft.
- Using the head size. D is the bolt's nominal thread diameter.
- Ignoring the specification. Always follow the maker's torque value.
Tips
- Tighten in steps and in a cross pattern on flanges.
- Keep threads clean so friction stays consistent.
- Check your torque wrench's calibration regularly.
What next
Use this often? Add Bolt Torque to your Home screen.
Frequently asked questions
How does a bolt torque calculator work?
It uses T = K × D × F: torque equals the nut factor times the bolt diameter times the preload.
What nut factor should I use?
About 0.20 for typical dry steel threads, according to Wikipedia; lubricated threads use a lower value.
How much torque for a 1/2-inch bolt?
For 7,700 lbf of preload with K = 0.208, about 800 lb-in (66.7 lb-ft).
Why does lubrication change the torque?
It lowers friction, which Wikipedia says can reduce the torque needed by 15% to 25%.
How much of the torque clamps the joint?
Only about 10%; around 90% goes into friction under the head and in the threads.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.