Saved

Press the star next to a tool's name to save it.

All my tools

Pressure Converter

Enter a value in pounds per square inch and this pressure converter shows it in bars, or swap the units to convert bars to pounds per square inch. One pound per square inch is 0.0689476 bar.

Restored your last values ·

Your result opens on the next page.

Result

68.9476 bar

Enter a value to see the conversion.

See full result

To convert pounds per square inch to bars, multiply the number of pounds per square inch by 0.0689476. Both are units of pressure, so the relationship between them never changes. One pound per square inch is 0.0689476 bar. Enter a value and this pressure converter gives the answer straight away; swap the units to turn bars back into pounds per square inch.

Pressure formula

Bars = pounds per square inch × 0.0689476

To go the other way, multiply bars by 14.5038 to get pounds per square inch. Because the factor is fixed, the answer is the same every time, and you can reverse the conversion without losing accuracy.

How to use the pressure converter

  1. Enter the amount in pounds per square inch. Decimals are fine.
  2. Check the units. From is pounds per square inch and To is bars. Press Swap units to convert bars to pounds per square inch.
  3. Read the result, with the same amount in other pressure units in the table below.

Worked example

A measurement comes to 2,500 pounds per square inch. Multiply by 0.0689476 to get 172.3689 bar. Going the other way, 4 bars × 14.5038 = 58.0151 psi.

Pounds per square inch to bars conversion chart

These values cover amounts commonly converted between pounds per square inch and bars.

Pounds per square inch (psi)Bars (bar)
1 psi0.0689476 bar
5 psi0.344738 bar
10 psi0.689476 bar
14.5 psi0.99974 bar
30 psi2.0684 bar
50 psi3.4474 bar
100 psi6.8948 bar
500 psi34.4738 bar
1,000 psi68.9476 bar
3,000 psi206.8427 bar

What is a pound per square inch?

A pound per square inch, written psi, is a unit of pressure from the US customary system. Pressure is the force applied perpendicular to a surface per unit of area, and psi expresses this as pounds of force on each square inch. It is the usual unit for tire pressure in the United States, and you will also see it on air compressors, pressure washers and hydraulic equipment. Gauge readings normally show the pressure relative to the air around them.

What is a bar?

The bar is a metric unit of pressure equal to exactly 100,000 pascals, where the pascal is the SI unit of one newton per square meter. One bar is close to, but slightly less than, the average pressure of the atmosphere at sea level. It is widely used for tire pressure in Europe, for weather and diving, and on industrial gauges. A millibar is one thousandth of a bar, and weather reports often use it.

Estimating in your head

For a rough answer, divide the number of pounds per square inch by about 14.5. Going the other way, multiply the number of bars by about 14.5. Rounded figures are fine for a quick check, but use the converter when the result matters, because small differences add up over large amounts. A useful habit is to write the unit beside every number, so that you can see at a glance which way the conversion should go. It also helps to compare the two units directly: one pound per square inch is 0.0689476 bar, and one bar is 14.5038 psi.

Converting pounds per square inch to bars in a spreadsheet

To convert a whole column of pounds per square inch in Excel or Google Sheets, put the pounds per square inch in column A and type =A1/14.50377377 in the first cell of column B, then fill the formula down. To go back from bars to pounds per square inch, use =A1*14.50377377. The rule is the same as on paper: divide the number of pounds per square inch by about 14.5. Check one row against this converter before you trust the whole column.

Rounding the answer

The converter shows up to six significant digits so that nothing is lost, but most real measurements don't need that much precision. Quote only as many digits as your original measurement supports. Always convert the full figure first and round only the final answer.

Reading the table of units

Under the main answer, the converter lists the same amount in other pressure units. You don't need a second converter if a form, a label or a teacher asks for a different unit: read it straight from the table. Change the From and To lists to make any of those units the main answer instead, or press Swap units to reverse the direction.

Checking your answer

A quick sense check catches most slips. The number of bars should be about 14.5 times smaller than the number of pounds per square inch. If your answer is far away from that, you may have multiplied when you should have divided.

Why exact conversions matter

Small errors in a conversion grow quickly when a figure is multiplied, shared or reused in another calculation. Using the exact definitions of the units, rather than a rounded rule of thumb, keeps results consistent between people, documents and software. This converter uses the defined relationship between pounds per square inch and bars for every answer, so the same input always gives the same result, and you can copy it straight into a report, a spreadsheet or a homework answer. When you share a converted figure, give its unit and say how you rounded it, so anyone can check your working.

Quick reference

One pound per square inch is 0.0689476 bar. Ten pounds per square inch is 0.689476 bar. One bar is 14.5038 psi.

Common mistakes

  • Multiplying instead of dividing. Check whether your answer should be larger or smaller.
  • Dropping digits. Round only at the end.
  • Mixing up similar units. Read the symbols carefully.

Try the blood pressure checker, the force calculator and the power converter all units.

These are the pressure conversions that people look up most often, with the factor for each direction. All of them work in the converter above: choose the two units, or press Swap units to reverse a pair.

ConversionFactorReverse conversionReverse factor
Bar to PSI× 14.50377377Pounds per square inch to bars× 0.06894757293
Bar to Atmosphere× 0.9869232667Atmospheres to bars× 1.01325
Bar to Torr× 750.0616827Torr to bars× 0.001333223684
Bar to kPa× 100Kilopascals to bars× 0.01
Bar to mmHg× 750.0615758Millimeters of mercury to bars× 0.001333223874
PSI to Atmosphere× 0.06804596391Atmospheres to pounds per square inch× 14.69594878
PSI to kPa× 6.894757293Kilopascals to pounds per square inch× 0.1450377377
Pascal to Atmosphere× 9.869 × 10⁻⁶Atmospheres to pascals× 101,325
Pascal to Bar× 1 × 10⁻⁵Bars to pascals× 100,000
Pascal to PSI× 0.0001450377377Pounds per square inch to pascals× 6,894.757293
Pascal to Torr× 0.007500616827Torr to pascals× 133.3223684
Pascal to kPa× 0.001Kilopascals to pascals× 1,000
Pascal to mmHg× 0.007500615758Millimeters of mercury to pascals× 133.3223874

More about the pressure units

  • Pascal (Pa). The pascal, written Pa, is the unit of pressure in the International System of Units. It's named after Blaise Pascal, and it's defined as one newton per square meter.
  • Kilopascal (kPa). The kilopascal, written kPa, is a unit of pressure equal to 1,000 pascals. The pascal is the SI unit of pressure, defined as one newton per square meter, and the kilopascal is a far more practical size for everyday measurements.
  • Bar (bar). The bar is a metric unit of pressure equal to exactly 100,000 pascals, where the pascal is the SI unit of one newton per square meter. One bar is close to, but slightly less than, the average pressure of the atmosphere at sea level.
  • Pound per square inch (psi). A pound per square inch, written psi, is a unit of pressure from the US customary system. Pressure is the force applied perpendicular to a surface per unit of area, and psi expresses this as pounds of force on each square inch.
  • Atmosphere (atm). The standard atmosphere, written atm, is a unit of pressure defined as 101,325 pascals. It's sometimes used as a reference or standard pressure, and it's approximately equal to Earth's average atmospheric pressure at sea level.
  • Millimeter of mercury (mmHg). A millimeter of mercury, written mmHg, is a manometric unit of pressure. It was originally defined as the extra pressure generated by a column of mercury one millimeter high, and it's now defined as exactly 133.322387415 pascals.
  • Torr (Torr). The torr is a unit of pressure based on an absolute scale, and it's defined as exactly 1/760 of a standard atmosphere, or about 133.32 pascals. It was originally intended to be the same as one millimeter of mercury, but later redefinitions made it very slightly lower.

What next

Use this often? Add Pressure to your Home screen.

Frequently asked questions

How does the pressure converter work?

It uses the fixed relationship between the two units: one pound per square inch is exactly a set fraction or multiple of one bar.

How many bars are in a pound per square inch?

One pound per square inch is about 0.06895 bars.

How many pounds per square inch are in a bar?

One bar is about 14.50 pounds per square inch.

How do I convert bars to pounds per square inch?

Press Swap units, then enter the number of bars.

How do I convert psi to mmHg?

Multiply by about 51.715. One pound per square inch is about 51.715 millimeters of mercury, so 2 psi is about 103.43 mmHg.

What are the most common pressure conversions?

Among the pairs people look up most are bars to pounds per square inch (multiply by 14.50377377); bars to atmospheres (multiply by 0.9869232667); bars to torr (multiply by 750.0616827); and bars to kilopascals (multiply by 100). The table of popular conversions on this page lists the rest.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters