Saved

Press the star next to a tool's name to save it.

All my tools

Torque Converter

Enter a torque and pick its unit to see it in newton-meters, pound-feet, pound-inches and more. This torque converter shows the formula and every unit at once.

Restored your last values ·

Your result opens on the next page.

Result

73.7562 lbf·ft

Enter a value to see the conversion.

See full result

A torque converter changes a torque value from one unit to another. Enter a figure in newton-meters to see it in pound-feet, or choose any pair from newton-centimeters, kilonewton-meters, pound-inches, ounce-inches, kilogram-force meters, kilogram-force centimeters and dyne-centimeters. One newton-meter is 0.737562 lbf·ft. This torque converter is handy when a manual gives a tightening figure in one unit and your torque wrench is marked in another.

Newton-meters to pound-feet formula

Pound-feet = newton-meters × 0.737562

To go the other way, multiply pound-feet by 1.3558 to get newton-meters. The factor comes from the exact definitions of the pound-force and the foot, so it never changes.

How to use the torque converter

  1. Enter the torque. Decimals such as 7.5 are fine.
  2. Choose the units. From starts at newton-meters and To at pound-feet. Pick any pair, or press Swap units.
  3. Read the result. The converted torque appears straight away, with the same torque in every other unit in the table below it.

Worked example

A car's service manual says to tighten the wheel nuts to 110 newton-meters, but your torque wrench is marked in pound-feet. Multiply 110 by 0.737562 and you get 81.1318 lbf·ft. Going the other way, a bolt specified at 80 pound-feet needs 108.4654 N·m. For a small fastener given as 12 newton-meters, change the To unit to pound-inches, because a small torque wrench is usually marked in that unit.

Newton-meters to pound-feet chart

These values cover the torques most often found in car, motorcycle and bicycle manuals.

Newton-meters (N·m)Pound-feet (lbf·ft)
5 N·m3.6878 lbf·ft
10 N·m7.3756 lbf·ft
20 N·m14.7512 lbf·ft
50 N·m36.8781 lbf·ft
80 N·m59.005 lbf·ft
100 N·m73.7562 lbf·ft
110 N·m81.1318 lbf·ft
150 N·m110.6343 lbf·ft
200 N·m147.5124 lbf·ft
300 N·m221.2686 lbf·ft

What is torque?

In physics and mechanics, torque is the rotational correspondent of linear force. It's also called the moment of force, or simply the moment. Just as a linear force is a push or a pull applied to a body, a torque can be thought of as a twist applied to an object around a chosen axis. When you drive a screw, the screwdriver applies torque to the screw and makes it tend to rotate. Torque has the dimension of force times distance, which is why every unit in this converter pairs a unit of force with a unit of length.

The torque units explained

  • Newton-meter (N·m). The SI unit for torque: a force of one newton acting at the end of a one-meter arm.
  • Newton-centimeter (N·cm) and kilonewton-meter (kN·m). A hundredth and a thousand times the newton-meter, for small parts and for heavy machinery.
  • Pound-foot (lbf·ft). One pound of force at the end of a one-foot arm. It's common in the United States, and it's often called a foot-pound.
  • Pound-inch (lbf·in) and ounce-inch (ozf·in). Smaller units for small fasteners and small electric motors. Twelve pound-inches make one pound-foot.
  • Kilogram-force meter (kgf·m) and kilogram-force centimeter (kgf·cm). Older metric units still seen on some tools and in older manuals.
  • Dyne-centimeter (dyn·cm). A very small unit from the centimeter-gram-second system.

Why torque isn't measured in joules

A newton-meter of torque is dimensionally equivalent to a joule, the unit of energy, because both are a force multiplied by a distance. Even so, the joule isn't used for torque. Torque is a twisting effect with a direction, while energy is a plain amount, so the two are physically distinct. Official SI literature gives the newton-meter as the standard unit for torque, and this converter follows that.

Reading a torque wrench

Many torque wrenches carry two scales, one in newton-meters and one in pound-feet. If yours has only one, convert the figure from the manual before you start, and write it down. Set the wrench to the converted value and tighten until it clicks or the pointer reaches the mark. Round sensibly: a setting of 73.7562 lbf·ft can be set as the nearest mark on the scale, since a wrench can't be set more finely than its markings.

Small torques: pound-inches and ounce-inches

For bicycle parts, electronics and small engines, figures are often given in pound-inches. One pound-foot is exactly 12 pound-inches, and one pound-inch is 16 ounce-inches. Mixing up pound-feet and pound-inches is a classic way to snap a small bolt, because the first is twelve times the second. If a figure looks far too high or far too low for the size of the fastener, check the unit again before you tighten anything.

Metric kilogram-force units

Some older manuals quote torque in kilogram-force meters, sometimes written kgm. One kilogram-force meter is the torque from one kilogram's weight at the end of a one-meter arm, and it equals 9.80665 newton-meters. As a rough guide, multiply kilogram-force meters by ten to get newton-meters, then use the converter for the exact value.

Common mistakes

  • Confusing pound-feet with pound-inches. They differ by a factor of twelve.
  • Treating newton-meters as joules. The units look alike, but torque and energy are different quantities.
  • Rounding before converting. Convert the full figure, then round the answer to the nearest mark on your wrench.
  • Ignoring the manual's conditions. A figure may assume dry or oiled threads, so read the note beside it.

Work out a force with the force calculator, change power units with the power converter, and convert pressures with the pressure converter.

What next

Use this often? Add Torque to your Home screen.

Frequently asked questions

How do I use the torque converter to change Nm to ft-lb?

Enter the torque in newton-meters and read the result in pound-feet. For example, 100 newton-meters is 73.7562 lbf·ft.

How many newton-meters are in a pound-foot?

One pound-foot is 1.3558 N·m.

Is a foot-pound the same as a pound-foot?

For torque, yes. Both names describe one pound of force acting at the end of a one-foot arm.

How do I convert pound-feet to pound-inches?

Multiply by 12. One pound-foot is exactly 12 pound-inches.

Is a newton-meter the same as a joule?

No. They have the same dimensions, but the joule is a unit of energy and isn't used for torque.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters