Saved

Press the star next to a tool's name to save it.

All my tools

Tree Age Calculator

Use this tree age calculator to estimate how old a tree is from its trunk circumference and species: it works out the diameter and multiplies by a growth factor.

Restored your last values ·

Measure the trunk around its widest part at breast height, 4.5 feet (1.3 metres) above the ground. Pick the species, or type a growth factor for a tree that is not in the list. You get the diameter and a rough age.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose the species, enter the trunk circumference, then press Calculate.

See full result

A tree age calculator gives a rough age for a living tree without cutting it down. You measure the circumference of the trunk, choose the species, and the tool turns the circumference into a diameter and multiplies it by a growth factor for that species.

How to use the tree age calculator

  1. Measure around the trunk at breast height, 4.5 feet or 1.3 metres above the ground.
  2. Choose US or metric units and enter the circumference.
  3. Pick the species, or type your own growth factor.
  4. Press Calculate.

The two formulas

The method uses two steps. First, the diameter at breast height, or DBH, is the circumference divided by 3.14, which is how the Purdue Landscape Report gives it: c divided by 3.14 equals d [1]. Second, the age in years is the DBH in inches multiplied by a growth factor [1]. Another garden-magazine guide gives the same first step in words: divide the circumference by pi, and the answer is the diameter [3].

What is the growth factor

The growth factor is a number of years of age for each inch of trunk diameter. A fast-growing tree, such as a cottonwood, has a small factor of 2, because each inch of diameter takes only about two years. A slow tree has a larger one. The Allegheny County list runs from 2 for cottonwood, quaking aspen and black willow to a range of 4 to 8 for the common horse chestnut, where the tool uses the top value [2], and many species have a factor of 3, 4 or 5 [2].

Where the table comes from

The species factors in the list follow the table in the Allegheny County Parks guide, which uses a formula published by the International Society of Arboriculture [2]. The Purdue report gives a factor of 5.0 for white oak [1], which matches the table. The Purdue chart itself is an image that we could not read, so we could not compare any other species with it. Treat the other factors as the table's values, not as measurements of our own.

A worked example

Take a red maple with a circumference of 6 feet 3 inches, which is 75 inches. The diameter is 75 divided by 3.14, or 23.89 inches, or about 61 centimetres. The red maple factor is 4.5 [2], so the age is 23.89 times 4.5, which rounds to 107 years. Enter 75 with red maple to see 107.48 years before rounding, and 60.67 centimetres for the diameter.

A second example

The Purdue article takes a white oak with a circumference of 5 feet 10 inches, or 70 inches. It divides by 3.14 and rounds the diameter to 22 inches, then multiplies by 5.0 to give 110 years [1]. The tool does not round the diameter, so for 70 inches it shows 22.29 inches and 111.46 years, which is the same result without the rounding. The two answers agree to within a year.

A very rough estimate

Purdue calls the result a very rough estimate [1]. The factor is an average for the species, so a tree that grew quickly in rich soil may be younger than the figure, and a stunted tree may be older. Our own caution is that a tree in an open yard may grow faster than the table assumes, which would make the estimate too high. Use the age as a range, such as 100 to 115 years, not as an exact date.

Metric measurements

If you choose metric, the tool divides the centimetres by 2.54 to get inches, and then continues as before. A circumference of 190.5 centimetres is 75 inches and gives the same 107 years. The result shows the diameter in both inches and centimetres, so you can compare it with a tape or a calliper. The 2.54 conversion is our own working and is exact by definition.

Species that are not listed

If your tree is not in the list, choose Other species and type a growth factor. Many species in the Allegheny County list have factors of 3, 4 or 5 [2], so 4 is a reasonable middle guess, and you can try 3 and 5 for a range. A growth factor you type always replaces the species setting. If you know the factor for your own region from a local forester, use that, as it is likely better than a general table.

Diameter instead of circumference

If you have measured the diameter, for example with a diameter tape or from a plan, type it in the diameter box and leave the circumference blank. The tool then skips the division by 3.14. If both boxes are filled in, the circumference is used and the diameter is ignored, and the result says so. A trunk with a buttress, a lean or a fork needs care: measure below the swelling or fork.

Better ways to date a tree

Counting the rings of a core sample or of a stump is more accurate than a formula, but it needs a tool and affects the tree, so a forester usually does it. Old records, such as a planting date for a street tree, are better still. Use this calculator when you need a quick estimate, for a school project, a garden plan or simple curiosity, and bear in mind that the figure is only a rough guide.

Common mistakes

  • Measuring at the wrong height. Measure at 4.5 feet or 1.3 metres, not at the base, where trunks flare.
  • Mixing units. Choose the matching unit setting before you type the number.
  • Using the wrong species. The factor changes the age a lot, so check the identification.
  • Treating the age as exact. It is a very rough estimate, so quote a range.

What next

Use this often? Add Tree Age to your Home screen.

Frequently asked questions

What is a tree age calculator?

A tool that estimates a living tree's age from its trunk circumference and a growth factor for its species.

How do you work out the age of a tree?

Divide the circumference by 3.14 to get the diameter at breast height, then multiply the diameter in inches by the species growth factor.

What is the growth factor?

The number of years of age per inch of trunk diameter, which differs by species. Most factors are 3, 4 or 5.

How accurate is the tree age calculator?

It is a very rough estimate. Counting the rings of a core sample is more accurate.

Where do I measure the trunk?

At breast height, 4.5 feet or 1.3 metres above the ground.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools