Saved

Press the star next to a tool's name to save it.

All my tools

Taper Calculator

Use this taper calculator to work out the taper per foot or per meter, taper ratio and angle from a part's large and small diameters and length.

Restored your last values ·

Measure both diameters and the length along the axis between them, in the same unit.

Everything is worked out in your browser. Nothing you type is sent anywhere.

Taper

–

Enter the two diameters and the length, then press Calculate.

See full result

This taper calculator works out the taper of a shaft, hole or tool shank from its two diameters and length. Enter the large and small diameters and the length between them, and the taper calculator gives the taper per foot (or per meter), the taper per inch, the ratio, the angle from the centerline and the included angle.

How to use the taper calculator

  1. Choose inches or millimeters.
  2. Enter the large diameter and the small diameter.
  3. Enter the length of the taper, measured along the axis.
  4. Press Calculate.

Ways of expressing a taper

The Wikipedia article on machine tapers shows that tapers are described in several ways: as a change in diameter per foot or per inch of length, as a ratio such as 1:20, or as an angle. Morse tapers, for example, are about 5/8 inch per foot (roughly 52 mm per meter), just under 1.5° from the centerline. Brown & Sharpe tapers are close to 0.500 inch per foot, and Jarno tapers are 0.600 inch per foot, which is 1:20 on the diameter or 0.050 inch per inch, at 1.4321° from the center.

The taper formulas

With large diameter D, small diameter d and length L:

  • Taper per unit length = (D − d) ÷ L
  • Taper per foot = (D − d) ÷ L × 12, when L is in inches
  • Ratio = 1 : L ÷ (D − d)
  • Angle from the centerline = arctan((D − d) ÷ 2L)
  • Included angle = 2 × the angle from the centerline

The angle uses half the difference in diameter, because each side of the taper only moves in by half of the total change.

Worked example

Wikipedia describes a No. 7 Jarno taper as 0.875 inch at the large end, 0.700 inch at the small end and 3.50 inches long. The taper is (0.875 − 0.700) ÷ 3.5 = 0.050 inch per inch, or 0.600 inch per foot, a ratio of 1:20. The angle from the centerline is arctan(0.175 ÷ 7) = 1.4321°, matching the value Wikipedia gives, and the included angle is 2.8642°.

Reading the results

The big number is the taper per foot for inches, or per meter for millimeters. The table shows the taper per unit length, the ratio, the angle from the centerline and the included angle.

Setting up a lathe

To turn a taper with the compound rest or a taper attachment, you set the angle from the centerline, not the included angle. For a tailstock offset, the offset depends on the overall length of the workpiece as well as the taper. Always take a light cut and check the taper with a gauge or by measuring both diameters before cutting to size.

Taper per foot and per meter

In the US, tapers are often given in inches per foot, measured on the diameter. A taper of 0.600 inch per foot means the diameter changes by 0.6 inch over 12 inches of length, or 0.05 inch per inch. In metric, tapers are often given in millimeters per meter or as a ratio: Wikipedia gives the Morse taper as roughly 52 mm per meter. The calculator shows the taper per foot when you choose inches and per meter when you choose millimeters, along with the ratio, which is the same in any unit.

Standard tapers

Machine tools use standard tapers so tools and holders fit any machine of the same type. Wikipedia describes several: Morse tapers on drill press and lathe spindles and tailstocks, about 5/8 inch per foot; Brown & Sharpe tapers, about 1/2 inch per foot; Jarno tapers, 0.600 inch per foot; and steep NMTB tapers on milling machines, 3.500 inches per foot. Entering the dimensions of a shank lets you check which family it belongs to.

Checking a part

Measure both diameters at two marked points a known distance apart, rather than at the very ends where chamfers can mislead. The calculator works with any two points along the taper, because the taper per unit length is the same along its whole length.

Metric example

A part 40 mm long that tapers from 20 mm to 18 mm has a taper of 2 ÷ 40 = 0.05 mm per mm, or 50 mm per meter, a ratio of 1:20, the same as the Jarno taper in the inch example.

Inches or millimeters

Choose the unit that matches your drawing and enter all three measurements in it. The ratio and the angles are the same in any unit, because they depend only on the proportions of the taper. Only the taper per foot or per meter depends on the unit you choose.

Write the taper and angle on your drawing so you can set up the machine quickly next time.

For a quick check of a lathe setup, compare the measured taper with the one on the drawing before the final cut.

Common mistakes

  • Confusing per-side and per-diameter. Taper per foot is on the diameter.
  • Using the included angle on the compound. Set half of it.
  • Measuring length along the slope. Measure along the axis.
  • Mixing units. Use the same unit for all three.

Tips

  • Measure diameters at exact, marked points along the taper.
  • Check a standard taper against its published dimensions.
  • Use bluing to check the fit of a mating taper.

What next

Use this often? Add Taper to your Home screen.

Frequently asked questions

How does a taper calculator work?

It divides the difference in diameter by the length to get the taper, and uses arctan((D − d) ÷ 2L) for the angle.

How do you calculate taper per foot?

Taper per foot = (large diameter − small diameter) ÷ length in inches × 12.

What is the taper of a Morse taper?

About 5/8 inch per foot, just under 1.5° from the centerline, according to Wikipedia.

What is a 1:20 taper in degrees?

About 1.4321° from the centerline, or 2.864° included.

Do I set the half angle or the included angle on a lathe?

The angle from the centerline, which is half the included angle.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools