A spindle speed calculator gives the rpm for a drill, mill or lathe from the diameter of the tool or the workpiece and the cutting speed. It also gives the cutting speed for a given rpm, a speed range for common materials, and the feed rate from the number of teeth and the chip load.
How to use the spindle speed calculator
- Choose US or metric units and what you want.
- Enter the diameter and the cutting speed or the rpm.
- Add teeth and chip load for the feed rate.
- Press Calculate.
The formula
In metric units the cutting speed is v = π D N ÷ 1000, in metres per minute, with D in millimetres and N the spindle speed in rpm [1]. Solving for the spindle speed gives N = 1000 v ÷ (π D). In US units, with the speed in feet per minute and the diameter in inches, the page gives RPM = cutting speed × 12 ÷ (π × diameter) [1]. The calculator uses these, and the page notes that a machinist may take π as 3 for a quick estimate [1], which the working line also shows.
Worked examples
The page's metric example is a cutting speed of 30 metres per minute on a 10 millimetre tool, which gives 1,000 rpm with π taken as 3 and 955 rpm with the accurate value [1]. Its US example is 100 feet per minute on a 10 inch diameter, which gives 40 rpm with the approximation and 38.2 rpm accurately [1]. The calculator returns the accurate values and the rough estimate beside them.
Typical cutting speeds
The page lists surface speeds for plain high-speed steel tools used dry with a tool life of one hour. For mild steel they are 3 to 38 metres per minute, which is 10 to 125 feet per minute, for free-cutting steels 35 to 69 metres per minute, for stainless steels 23 to 40 metres per minute, for brass 90 to 210 metres per minute, for aluminium 122 to 305 metres per minute and for wood 183 to 305 metres per minute [1]. Pick a material to see the rpm range for your tool diameter.
A wide range
The ranges are wide because the right speed depends on the alloy, the tool material, the depth of cut and whether coolant is used. The page warns that the figures change with coolant or improved tool grades [1]. Use the table to find a starting point and adjust by the sound and finish of the cut, or follow the tool maker's recommendation, which is usually more specific.
Feed rate
For a milling cutter, the feed rate is the rpm times the number of teeth times the chip load, FR = RPM × T × CL, in inches or millimetres per minute [1]. The page says that this does not apply to turning on a lathe, where the feed is given per revolution [1]. For a 10 millimetre cutter at 955 rpm with 4 teeth and a chip load of 0.1 millimetre per tooth, the feed rate is about 382 millimetres per minute, our own example with the page's formula.
Cutting speed from rpm
If your machine has fixed speeds, you can work the other way. Enter the diameter and the rpm you can set, and the calculator gives the cutting speed that results. Compare it with the range for the material. If it is above the range, choose a lower speed or a smaller tool, and if it is far below, you may be cutting slower than needed.
Diameter
For a drill or a milling cutter, use the diameter of the tool. For turning on a lathe, use the diameter of the workpiece at the cut, which changes as material is removed. Because the speed depends on the diameter, a larger part needs a lower rpm to keep the same surface speed. Recalculate when the diameter changes much.
Setting a machine with fixed speeds
Many drill presses and older lathes have a belt with a few fixed speeds. Work out the ideal rpm, then pick the nearest speed that is not above it, since running a little slow is safer for the tool than running fast. Then use the second mode to check the cutting speed that the chosen setting gives, and compare it with the range for the material.
Small tools run fast
Because rpm rises as the diameter falls, small tools need very high speeds. A 3 millimetre drill in aluminium at a cutting speed of 100 metres per minute needs about 10,600 rpm, which is beyond the range of many drill presses. In that case, run at the top speed of the machine, accept a lower cutting speed and feed gently. Check the result with the calculator to see how far below the target you are.
Safety
Never exceed the maximum speed marked on a tool, grinding wheel or chuck. Secure the work, wear eye protection and keep loose clothing and hair away from the spindle.
Common mistakes
- Using the radius. Enter the diameter.
- Mixing the units. Feet per minute go with inches.
- Applying the table to carbide tools. The ranges are for plain high-speed steel.
- Using the milling feed formula on a lathe. Lathe feed is per revolution.
What next
Use this often? Add Spindle Spee to your Home screen.
Frequently asked questions
What is a spindle speed calculator?
A tool that finds the rpm of a drill, mill or lathe from the cutting speed and the diameter.
What is the formula for rpm?
N = 1000 v ÷ (π D) with v in metres per minute and D in millimetres, or N = 12 v ÷ (π D) with v in feet per minute and D in inches.
How do I find the feed rate?
Feed rate = rpm × number of teeth × chip load, for milling.
What cutting speed should I use for aluminium?
The page lists 122 to 305 metres per minute (400 to 1,000 feet per minute) for plain high-speed steel tools, dry.
Can I use π as 3?
Yes, for a quick estimate. The accurate result is about 5 percent lower.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.