A miter angle calculator gives the angle at which to cut each of two pieces so that they meet in a clean corner. Enter the number of sides of a frame, box or polygon, or the angle at which the pieces meet, and it returns the cut angle and the saw setting.
How to use the miter angle calculator
- Choose whether you know the number of sides or the meeting angle.
- Enter the value.
- Press Calculate.
The rule
A miter joint is made by cutting each of two parts across the main surface, usually at 45°, so that they meet at a corner, usually of 90° [1]. To find the cut angle, divide the angle at which the two pieces meet by two [1]. For a 90° corner that gives 45° on each piece. For two pieces that meet at 120° each is cut at 60°, a result of the same rule.
Polygons
For a frame with n equal sides, the interior angle at each corner is 180° × (n − 2) ÷ n, which is our own working from the geometry of the polygon. A square has 90°, a hexagon 120° and an octagon 135°. The page shows a disassembled 135° miter joint, the interior angle of an octagon [1], so the cut angle for each piece of an octagonal frame is 135° ÷ 2 = 67.5° to the edge of the piece.
The saw setting
Most miter saws read their scale from a square cut, where the blade is at 90° to the fence and the scale shows zero. The setting is then 90° minus the cut angle to the edge, which gives 45° for a square frame and 22.5° for an octagon. The octagon value of 22.5° matches the example on the page [1], and common saws have stops at 15°, 22.5°, 30° and 45° [2]. The calculator shows both numbers, since books and saws use different conventions.
Two cut angles
The page notes that, technically, two different cut angles are needed, one for each piece, where the second angle is 90° plus the cut angle [1]. In practice, a single saw setting is used for both pieces, in opposite directions [1]. Cut one piece with the saw turned to the left and the other with it turned to the right, or flip the piece over.
Miter and bevel
The two terms describe different cuts. The page defines a miter cut as one made across the face, and calls it beveling when the angled cut is done on the side, though the result is still a miter joint [1]. On a miter saw, swivelling the table gives a miter cut with the blade vertical and angled across the work, and rotating the head gives a bevel cut with the blade tilted from vertical [2]. A cut that does both is a compound cut [2]. This calculator covers the simple flat miter.
Worked examples
A picture frame with four sides: the meeting angle is 90°, each piece is cut at 45°. A hexagonal planter box: the interior angle is 120°, so each piece is cut at 60° to its edge, and the saw is set to 30°. An eight-sided gazebo base: the angle is 135° and the saw setting is 22.5°. A corner in a wall of 150° needs a setting of 15°. These are our own calculations from the rule.
Getting a good fit
Measure the outside length of each piece, since the long edge of a mitered piece is the longer one. Cut a pair of test pieces from scrap and check that they close up. Small errors add up around a frame, so a gap of a degree at each of eight corners is visible. Adjust the setting by a fraction of a degree if you need to.
Frames with unequal corners
Not every corner is a right angle. A bay window, a roof trim or a wall that bends may have corners of 100 or 150 degrees. For those, measure the angle with an angle finder, choose the meeting-angle option and read the setting. Each piece is half the measured angle, so if the corner is not symmetrical, for instance when one side is a sloping surface, you may need different settings for the two pieces, and a test cut will show it.
Checking a polygon
The interior angles of a polygon add up to 180 degrees times two fewer than the number of sides, and they are equal in a regular polygon. For a hexagon that is 720 degrees, so each corner is 120 degrees. Checking this sum is a quick test that the number of sides you entered matches the shape you are building. The calculator does the division for you, but it is worth knowing why the numbers come out.
Cutting list tip
Write the cut angle on each piece before you cut, along with which end it applies to, so that mirrored pairs do not get mixed up. This avoids the most common mistake in framing: two pieces cut the same way that cannot form a corner.
Common mistakes
- Using the saw scale in the wrong convention. Check whether zero is a square cut.
- Setting the saw to the full corner angle. Each piece takes half.
- Cutting both pieces the same way. Mirror the second piece.
- Skipping a test cut. Always test on scrap.
What next
Use this often? Add Miter Angle to your Home screen.
Frequently asked questions
What is a miter angle calculator?
A tool that gives the angle at which to cut two pieces so that they meet at a corner.
How do I find the miter angle?
Divide the angle at which the pieces meet by two. For a 90° corner that is 45°.
What miter angle do I use for an octagon?
The interior angle is 135°, so each piece is cut at 67.5° to its edge, which is a saw setting of 22.5°.
What is the difference between miter and bevel?
A miter swivels the blade across the face, and a bevel tilts the blade from vertical.
Do I need two different angles?
In practice, one saw setting is used, with the second piece cut in the opposite direction.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.