A shear strain calculator works out shear strain, and the stress and modulus that go with it. Choose to find the shear stress from a force and an area, the shear strain from a sideways displacement or from a stress and a modulus, or the shear modulus of a material from a test. It covers the shear modulus calculator and shear stress calculator jobs in one tool.
How to use the shear strain calculator
- Choose the units and what to find.
- Fill in the boxes that appear.
- Press Calculate.
Shear stress
Shear stress is the force acting along a surface divided by the area it acts over, τ = F ÷ A [2]. For example, a force of 500 newtons on an area of 0.01 square metres gives 50,000 pascals. In metric mode the stress is shown in megapascals.
Shear strain from displacement
Shear strain is the sideways displacement divided by the length across which it acts, γ = Δx ÷ h [3]. It has no unit. Wikipedia says that the engineering shear strain is the tangent of the shear angle, which is approximately equal to the angle in radians for small angles [3]. For a displacement of 1 millimetre over 100 millimetres, γ = 0.01, which is an angle of 0.573 degrees.
Shear strain from stress and modulus
Hooke's law for shear links the three quantities: τ = G × γ, which follows from the definition of the shear modulus [1]. So the strain is γ = τ ÷ G, which gives the angle itself. As an example for brass, with G = 3.5 × 10¹⁰ pascals and τ = 8.0 × 10⁶ pascals, the strain is about 2.3 × 10⁻⁴. Choose that option, enter 8 megapascals and 35 gigapascals, and you get 0.00022857.
Shear modulus
The shear modulus, also called the modulus of rigidity, is the ratio of the shear stress to the shear strain, G = τ ÷ γ = (F ÷ A) ÷ (Δx ÷ l) = F l ÷ (A Δx) [1]. Wikipedia defines it as the ratio of shear stress to shear strain, and gives its SI unit as the pascal, usually written in gigapascals or in ksi [1]. The calculator shows both.
The worked modulus example
As an illustration, take a force of 500 newtons, an area of 0.01 square metres, a length of 0.5 metres and a displacement of 0.0005 metres. The stress is 50,000 pascals, the strain is 0.001, and the modulus is 50 megapascals. In metric mode, enter 500, 10,000, 0.5 and 500 to get 0.05 gigapascals, the same value.
Typical values
Wikipedia's table gives the shear modulus of steel as 79.3 gigapascals, copper 44.7, aluminium 25.5, glass 26.2 and rubber 0.0006 [1]. The brass value above is only an illustration. Values vary with the alloy and the temperature, so check a data sheet for the material that you use. The calculator does not hold a materials table.
Units
In US mode, the force is in pound-force, lengths in inches, areas in square inches, stress in psi and the modulus in ksi, thousands of pounds per square inch, which Wikipedia names as a common unit [1]. In metric mode, use newtons, millimetres, megapascals and gigapascals. The results are also shown in the other system. Strain has no unit, so it is the same in both.
Torsion of a shaft
For a round shaft in torsion, Wikipedia gives the shear stress at radius r as τ = T r ÷ J and the angle of twist as φ = T L ÷ (G J) [4]. Dividing the first by G and using the second gives the shear strain γ = r φ ÷ L, with φ the angle of twist and L the length. This step is our own working. At the surface, it is the radius times the angle of twist divided by the length. This calculator does not do torsion directly, but the angle of twist calculator on this site does.
Limits
The formulas are for small deformations of a uniform, elastic material. A real body may be anisotropic, may yield, or may fail in other ways. The strain from a displacement uses the simple ratio, as the definition above does, so for large angles take the arctangent. The calculator reports the angle in degrees for this reason. It gives the values for study and checks only.
Using the calculator
Choose the job, enter the values and press the button. Check that the units are consistent: force with area, displacement with length. Try the brass example in the stress and modulus mode, then the 500 newton example in the modulus mode. If you test a material in a lab, the modulus mode gives G from the force, area, displacement and height of your sample.
A quick sense of scale
Shear strains in stiff solids are tiny. For brass loaded to 8 megapascals, the strain is 0.00023, an angle of about 0.013 degrees, so you could not see the deformation. Now take a small stress of 0.06 megapascals. Wikipedia's table gives the modulus of steel as 79.3 gigapascals and of rubber as 0.0006 gigapascals, which is 0.6 megapascals [1]. The strain in steel is then below one in a million, while in rubber it is 0.1, an angle of about 5.7 degrees that you can see. The comparison is our own working from the formula γ = τ ÷ G. A stiff material needs a large stress to shear by a small amount, while a soft material shears easily. Use the modulus mode on test data to check which material you have.
Common mistakes
- Mixing the area and the length. Area is in square units, length in units.
- Using a wrong angle. The ratio equals the angle only if it is small.
- Confusing G and E. G is for shear, E for tension.
- Using GPa with MPa. The calculator converts, but check your inputs.
What next
Use this often? Add Shear Strain to your Home screen.
Frequently asked questions
What is a shear strain calculator?
A tool that finds shear strain, and the shear stress or modulus that goes with it.
What is the formula for shear strain?
γ = Δx ÷ h from a displacement, or γ = τ ÷ G from a stress and modulus.
How do I calculate shear stress?
Divide the force acting along the surface by the area: τ = F ÷ A.
What is the shear modulus?
The ratio of shear stress to shear strain, G = τ ÷ γ, also called the modulus of rigidity.
What is the shear modulus of steel?
Wikipedia's table gives 79.3 GPa at room temperature; the value varies with the alloy.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.