An angle of twist calculator finds how far a round shaft twists when a torque is applied. Enter the torque, the length and the diameter of the shaft, and choose steel, aluminium or your own shear modulus. It gives the angle in radians and degrees, for a solid or a hollow shaft.
How to use the angle of twist calculator
- Choose the material and the shaft type.
- Enter the torque, the length and the diameter.
- Press Calculate.
The formula
For a prismatic member under a constant torque, the angle of twist is φ = T ℓ ÷ (G J), where T is the torque, ℓ the length, G the shear modulus and J the torsion constant [1]. The twist grows with the torque and the length, and falls with a stiffer material or a bigger section. For a circular section, the torsion constant is the polar second moment of area. The page notes that for non-circular sections the two are generally not the same [1].
Solid shaft
For a solid round shaft of diameter D, the torsion constant is J = π D⁴ ÷ 32 [1], which is the same as π R⁴ ÷ 2 with R the radius [1]. The diameter appears to the fourth power, so doubling it makes the shaft 16 times stiffer in torsion. A shaft of 50 millimetres has J = 613,592 mm⁴. With a torque of 1,000 newton metres and a length of 1 metre in steel, the twist is 0.02055 radians, or 1.1775 degrees.
Hollow shaft
For a hollow shaft, or tube, the page gives J = π ÷ 2 × (R_e⁴ − R_i⁴), with R_e and R_i the outer and inner radii [1]. Written with diameters this is π (D⁴ − d⁴) ÷ 32, a form that is our own rewriting of the radius formula. A tube of 50 millimetres outside and 40 millimetres inside has J = 362,265 mm⁴, which is about 59 percent of the solid shaft but it uses only 36 percent of the material. The same load twists it 1.9945 degrees.
Shear modulus
The shear modulus G is the stiffness of a material against shearing. The page lists typical values at room temperature: steel 79.3 GPa, aluminium 25.5 GPa, iron 52.5, copper 44.7, titanium 41.4, glass 26.2, granite 24 and wood 4 [2]. The calculator offers steel and aluminium, and lets you enter any other value. The same shaft in aluminium twists 3.6619 degrees, over three times as far as in steel.
Units
The calculator takes the torque in newton metres, the length in metres, the diameter in millimetres and the modulus in gigapascals, and it converts them to SI units inside. The result is in radians, with the equivalent in degrees. Keep the torque and the length of the part that carries the torque, since a shaft that is long but loaded only over a short part twists less.
Reading the result
A large twist angle means a flexible shaft. For a drive shaft or a torsion bar, designers often limit the twist per unit length, to keep a drive stiff, or to a spring rate in a torsion spring. The angle per metre is found by dividing the result by the length, which is the same as setting the length to 1 metre in the calculator.
Limits
The formula is for round sections of one material, with the torque applied evenly, and for stresses within the elastic range. Keyed shafts, splines, tapers and stress concentrations all change the real result. The calculator does not give the shear stress or the safety factor. A real shaft must also be checked for the bending loads, fatigue and the critical speed, so use this only for estimates.
Using the calculator
Select the material and the shaft type, then enter the torque, the length and the outer diameter. For a hollow shaft add the inner diameter. Check the working line for the torsion constant that was used. To compare designs, change one value at a time, such as the diameter, and see how strongly the twist responds, since it falls with the fourth power of the diameter.
Common checks
If the answer looks wrong by a large factor, check the diameter, which is easy to enter as a radius by mistake, and the units of the modulus. A steel shaft of 50 millimetres carrying 1,000 newton metres over 1 metre should twist by about one degree, which is a handy reference for a check.
Why the diameter matters so much
The twist of the example shaft is 1.1775 degrees per metre. If the diameter is halved to 25 millimetres, the torsion constant falls to one sixteenth, and the same torque twists the shaft 18.84 degrees. This fourth-power rule is why drive shafts are made as large as the space allows, and why tubes are so efficient: material near the axis adds little stiffness, while material at the outside adds a lot. These figures are our own calculations from the formula.
Torque and length
The twist is proportional to both the torque and the length. Double either of them and the angle doubles. A shaft of 2 metres therefore twists twice as far as a shaft of 1 metre under the same torque, which is why long shafts are often supported by intermediate couplings or stiffened by a bigger diameter.
Common mistakes
- Entering the radius as the diameter. The diameter is to the fourth power.
- Using the wrong modulus. Steel and aluminium differ by a factor of three.
- Using it for non-round sections. The formula is for round shafts.
- Treating it as a safety check. It gives only the twist.
What next
Use this often? Add Angle of Twi to your Home screen.
Frequently asked questions
What is an angle of twist calculator?
A tool that finds how far a round shaft twists under a torque.
What is the formula for the angle of twist?
φ = T ℓ ÷ (G J).
What is J for a solid round shaft?
J = π D⁴ ÷ 32.
What is the shear modulus of steel?
About 79.3 GPa; aluminium is about 25.5 GPa.
Why does a bigger diameter help so much?
The twist falls with the fourth power of the diameter.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.