Saved

Press the star next to a tool's name to save it.

All my tools

Elongation Calculator

Use this elongation calculator to find how much a bar stretches under a load from its length, area and Young's modulus, and the percent elongation of a test piece from its two lengths.

Restored your last values ·

Choose US or metric units. For the stretch of a bar, enter the load, the length, the area and the Young's modulus. For the percent elongation of a test piece, enter the lengths before and after.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what you want and fill in the boxes, then press Calculate.

See full result

An elongation calculator finds how far a bar stretches under an axial load, from the load, the length, the area and the Young's modulus, and also finds the percent elongation of a test piece from its lengths before and after a test. It works in US or metric units.

How to use the elongation calculator

  1. Choose US or metric units and what you want.
  2. Enter the load, length, area and modulus.
  3. Press Calculate.

Stress and strain

The stress in a bar is the force divided by its original cross-sectional area, σ = F ÷ A₀ [1]. The strain is the change in length divided by the original length, ε = (L − L₀) ÷ L₀, and it has no units [1]. In the elastic range, stress and strain are proportional: σ = E ε, where E is Young's modulus [1]. This is Hooke's law for a bar.

The stretch

Combining the three relations gives the elongation ΔL = ε L = F L ÷ (A E). This step is our own working, since the pages that we read give the pieces and not the final formula. For a load of 10 kilonewtons on a bar of 100 square millimetres and 2,000 millimetres long, with a modulus of 200 gigapascals, the stress is 100 megapascals, the strain is 5 × 10⁻⁴ and the bar stretches 1 millimetre.

A US example

A bar of 0.25 square inches and 20 inches long, loaded with 2,000 pounds-force, with a modulus of 29 million psi, has a stress of 8 ksi and a strain of 0.000276, so it stretches 0.0055 inches. The calculator converts the units to SI and back. The example is our own. The modulus of steel, about 200 gigapascals or 29 million psi, is our own figure, and the pages give none.

Elastic range

The formula holds only while the material is elastic, that is, until it is unloaded and returns to its original length. The page says that the linear relation holds only in the elastic range [1]. If the stress is above the yield strength, the bar stretches by more than the formula says, and does not fully recover. The calculator warns if the stress is very high compared with the modulus.

Percent elongation

The percent elongation of a test piece is %EL = (l_f − l₀) ÷ l₀ × 100, where l_f is the length after fracture and l₀ is the original length [2]. It is also called the elongation at break. A piece of 50 millimetres that is 57.5 millimetres long after it breaks has an elongation of 15 percent. It measures how ductile the material is.

Ductility

The page says that the elongation of ductile metals and some organic materials ranges from 1.2 percent to over 1,200 percent [2]. It quotes the textbook of Shigley, which says that about 5 percent elongation is significant [2]. The calculator mentions this when the result is 5 percent or more. A material with a low elongation, such as glass or cast iron, is brittle.

Units

In US mode, the load is in pounds-force, the length in inches, the area in square inches and the modulus in millions of psi. In metric mode, the load is in kilonewtons, the length in millimetres, the area in square millimetres and the modulus in gigapascals. The result is in inches or millimetres, with the strain and the stress. The conversion factors are our own.

Several loads

For a bar with several sections or loads, work out the elongation of each part and add them. The stretch is proportional to the load, so doubling the load doubles it, and it is also proportional to the length. A bar of half the area stretches twice as far. You can see this by changing one value at a time in the calculator.

Limits

The formula is for a straight bar of uniform section and a single material, with the load along its axis. It does not cover bending, thermal expansion or a change in the load along the bar, such as the weight of the bar itself. For a long hanging cable, the self-weight adds a stretch that is not included here.

Using the calculator

Pick the units and the mode, and enter the values. For the stretch, read the elongation, the strain and the stress. Check that the stress is below the yield strength of the material. For the percent elongation, enter the two lengths and compare the result with the ductility that is needed for your material.

Stiffness of a bar

The ratio of the load to the stretch, A E ÷ L, is the axial stiffness of the bar. For the metric example, it is 100 mm² × 200,000 N/mm² ÷ 2,000 mm, which is 10,000 newtons per millimetre. A shorter or thicker bar is stiffer, and one of a stiffer material is stiffer as well. Use the calculator to find which change gives the stiffness that you need.

Common mistakes

  • Using the diameter instead of the area. Enter the area.
  • Using a modulus in the wrong units. GPa or Msi.
  • Using it above the yield stress. The formula is for the elastic range.
  • Confusing strain and percent. Strain 0.01 is 1 percent.

What next

Use this often? Add Elongation to your Home screen.

Frequently asked questions

What is an elongation calculator?

A tool that finds how much a bar stretches under a load, or the percent elongation of a test piece.

What is the formula for elongation?

ΔL = F L ÷ (A E) in the elastic range.

What is percent elongation?

(l_f − l₀) ÷ l₀ × 100, the stretch at fracture as a percentage of the original length.

What is Hooke's law for a bar?

Stress equals Young's modulus times strain, σ = E ε.

What elongation is significant?

About 5 percent or more, according to a standard textbook.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools