This sag calculator works out how much a cable, wire or rope sags between two supports under its own weight. Enter the span, the cable's weight per foot and its horizontal tension, and the sag calculator gives the sag at mid-span, the tension at the supports and the length of cable. Or enter the sag you want, and it works out the tension needed.
How to use the sag calculator
- Choose US or metric units. US (feet and pounds) is the default.
- Choose what to work out: sag from tension, or tension from sag.
- Enter the span between the supports and the cable's weight per foot or meter.
- Enter the horizontal tension or the sag, then press Calculate.
The catenary
A flexible cable hanging under its own weight takes the shape of a catenary. The Wikipedia article on catenaries explains that, with the cable's lowest point as the vertex, the curve is y = a × cosh(x ÷ a), where a = T0 ÷ w: the horizontal tension at the lowest point divided by the weight per unit length. In other words, a is the length of cable whose weight equals that tension. The horizontal part of the tension is the same all along the cable, while the vertical part grows with the length of cable between the point and the vertex.
The sag formulas
For supports at the same height, a span L apart, the lowest point is in the middle. Using the catenary equation and its arc length, s = a × sinh(x ÷ a):
- Sag = a × (cosh(L ÷ 2a) − 1)
- Cable length = 2a × sinh(L ÷ 2a)
- Tension at each support = T0 × cosh(L ÷ 2a)
To find the tension for a given sag, the calculator searches for the value of a that gives that sag, then multiplies by the weight.
Worked example
A cable weighing 0.5 pounds per foot spans 100 feet with a horizontal tension of 500 pounds. Then a = 500 ÷ 0.5 = 1,000 feet. The sag is 1,000 × (cosh(0.05) − 1) = 1.25 feet, the cable is about 100.04 feet long, and the tension at each support is about 500.6 pounds. Halving the tension to 250 pounds about doubles the sag, to about 2.5 feet.
Tension and sag
Sag and tension work against each other. Pulling a cable tighter reduces the sag, but the tension rises quickly as the cable gets close to straight, which is why a cable can never be pulled perfectly straight under its own weight. Allowing more sag lowers the tension on the cable and the supports. The calculator shows the support tension so you can check it against the cable's and anchors' ratings.
Catenary and parabola
Wikipedia notes that Galileo described a hanging cord as only an approximate parabola, almost exact when the angle of elevation is less than 45°. When the load is spread evenly along the horizontal span rather than along the cable, as with a suspension bridge deck much heavier than its cables, the shape is a parabola. The calculator uses the exact catenary, so it stays accurate even for large sags.
Reading the results
The big number is the sag (or the tension, in the second mode). The table shows the tension at each support, the cable length and how much longer the cable is than the span.
Finding the cable weight
The calculator needs the cable's weight per unit length. You can find it on the cable maker's data sheet, or weigh a measured length: if 10 feet of cable weighs 5 pounds, its weight is 0.5 pounds per foot. In metric, use newtons per meter; a cable with a mass of 1 kilogram per meter weighs about 9.8 newtons per meter.
Metric example
A cable weighing 7 newtons per meter over a 30-meter span with a horizontal tension of 2,000 newtons has a = 2,000 ÷ 7 ≈ 286 meters. The sag is about 0.39 meters, and the tension at each support is about 2,003 newtons.
Cable length
A sagging cable is always a little longer than the span between its supports. The table shows the cable length and the extra beyond the span. For a tight cable the difference is small, a few hundredths of a foot over 100 feet in the main example, but for a cable with a large sag it's much more, which matters when cutting cable to length.
Using the tension mode
If you know how much sag you can allow, for example to keep a line clear of the ground or a roof, choose Tension from sag. Enter the span, the weight and the sag, and the calculator finds the horizontal tension needed and the tension at the supports, so you can check the cable and anchors can take it.
Common mistakes
- Using the tension at the support. Enter the horizontal tension.
- Mixing weight units. Use pounds per foot or newtons per meter.
- Uneven supports. The formulas assume level supports.
- Ignoring ice and wind. They add load and change the sag.
Tips
- Weigh a measured length of cable to find its weight per foot.
- Check the support tension against the cable's rated strength.
- Allow for temperature: cables lengthen in heat and sag more.
What next
Use this often? Add Sag to your Home screen.
Frequently asked questions
How does a sag calculator work?
It uses the catenary: sag = a(cosh(L/2a) − 1), where a = horizontal tension ÷ weight per unit length.
How much does a 100-foot cable sag?
At 0.5 lb/ft and 500 lb of horizontal tension, about 1.25 feet.
Why can't a cable be pulled perfectly straight?
The tension needed rises without limit as the sag approaches zero.
Is a hanging cable a parabola?
No, it's a catenary; a parabola is a close approximation when the sag is small.
What is the tension at the supports?
The horizontal tension times cosh(L/2a), a little more than the horizontal tension.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.