This beam deflection calculator works out how far a beam bends under load. Choose a simply supported beam or a cantilever, a point load or a uniform load, enter the load, span, material and cross-section, and the beam deflection calculator gives the maximum deflection, the span-to-deflection ratio, the maximum bending moment and the maximum bending stress.
How to use the beam deflection calculator
- Choose US or metric units. US (pounds, feet and inches) is the default.
- Choose the supports and the load type.
- Enter the load and the span.
- Choose the material, or enter its Young's modulus, and the cross-section: a solid rectangle, or any shape's moment of inertia. Then press Calculate.
Beam deflection formulas
The Wikipedia article on deflection in engineering gives the maximum deflection for four common cases, where E is the material's Young's modulus and I is the beam's second moment of area (moment of inertia):
| Beam and load | Maximum deflection | Where |
|---|---|---|
| Simply supported, point load F at the center | F L³ ÷ (48 E I) | Center |
| Simply supported, uniform load q | 5 q L⁴ ÷ (384 E I) | Center |
| Cantilever, point load F at the free end | F L³ ÷ (3 E I) | Free end |
| Cantilever, uniform load q | q L⁴ ÷ (8 E I) | Free end |
The article notes that these formulas assume a slender beam (length more than about 10 times its depth), a linear elastic material and small deflections, under one-tenth of the span. Under those conditions they should be within about 5% of the actual deflection.
Material and cross-section
Young's modulus measures how stiff a material is. Wikipedia's table gives about 200 GPa (29 million psi) for A36 structural steel and about 68 GPa (9.9 million psi) for aluminium; the calculator uses these, or you can enter your own value. For a solid rectangle of width b and depth h, the second moment of area is I = b × h³ ÷ 12, so a beam on edge is much stiffer than the same beam laid flat. For other shapes, such as steel I-beams or tubes, enter I from the manufacturer's tables.
Bending moment and stress
The maximum bending moment comes from simple statics: for a simply supported beam it's F L ÷ 4 with a center point load and q L² ÷ 8 with a uniform load, and for a cantilever it's F L or q L² ÷ 2 at the fixed end. The Wikipedia article on bending gives the bending stress as σ = M × y ÷ I, where y is the distance from the neutral axis; the maximum is at the outer edge, half the depth from the center. For a custom section, enter its depth to see the stress.
Worked example
Take a steel beam with a moment of inertia of 30 in⁴ and a depth of 6 inches, simply supported over 10 feet (120 inches), with a 1,000-pound load at the center. The deflection is 1,000 × 120³ ÷ (48 × 29,000,000 × 30) = 0.041 inches, or about span ÷ 2,900. The maximum moment is 1,000 × 120 ÷ 4 = 30,000 lb·in (2,500 lb·ft), and the maximum stress is 30,000 × 3 ÷ 30 = 3,000 psi.
In metric, a steel cantilever 2 m long with I = 500 cm⁴ and a depth of 200 mm, carrying 2 kN at its end, deflects 5.33 mm, with a maximum moment of 4 kN·m and a stress of 80 MPa.
Reading the results
The big number is the maximum deflection. The table shows the span divided by the deflection, which is how deflection limits are often written, the maximum bending moment, the maximum bending stress and the moment of inertia used.
Why depth matters so much
Because the second moment of area of a rectangle grows with the cube of its depth, a deeper beam is far stiffer than a wider one. A 2 × 6 inch rectangle on edge has I = 2 × 6³ ÷ 12 = 36 in⁴, but laid flat it has only 6 × 2³ ÷ 12 = 4 in⁴, nine times less. Doubling the depth of a rectangle makes it eight times stiffer, while doubling the width only doubles it. That's why joists and beams are set on edge.
Span and deflection
Span has an even bigger effect. A point load's deflection grows with the cube of the span, and a uniform load's with the fourth power, so a beam twice as long sags 8 or 16 times as much under the same kind of load. When a beam deflects too much, a shorter span, a deeper section or a stiffer material helps most.
Uniform loads
A uniform load is spread evenly along the beam, such as the weight of a floor or a shelf full of books. Enter it per foot or per meter of length. A point load is a single concentrated weight, which the calculator places at the center of a simply supported beam or at the free end of a cantilever, the worst position for each.
Common mistakes
- Mixing units. Keep to the units shown for each field.
- Laying the depth flat. h is the vertical depth of the beam.
- Ignoring the beam's weight. Add it to a uniform load for long or heavy beams.
- Treating it as a design check. It doesn't check strength or codes.
Tips
- Compare a few depths: doubling the depth makes a rectangle 8 times stiffer.
- Use manufacturer tables for I-beams and tubes.
- Have structural work checked by an engineer.
What next
Use this often? Add Beam Deflect to your Home screen.
Frequently asked questions
How does a beam deflection calculator work?
It uses the standard deflection formulas, such as F L³ ÷ (48 E I) for a simply supported beam with a center load.
What is the formula for beam deflection with a uniform load?
5 q L⁴ ÷ (384 E I) for a simply supported beam, and q L⁴ ÷ (8 E I) for a cantilever.
What is the moment of inertia of a rectangle?
I = b × h³ ÷ 12, with b the width and h the depth.
How do you calculate bending stress?
σ = M × y ÷ I, where y is the distance from the neutral axis to the outer edge.
What is Young's modulus for steel?
About 200 GPa (29 million psi) for A36 structural steel.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.