A rolling resistance calculator finds the force that opposes a wheel rolling on a surface, from the vehicle mass and a rolling resistance coefficient. Pick a typical wheel and surface or enter your own coefficient, and add a speed to see the power needed to keep going on level ground.
How to use the rolling resistance calculator
- Choose US or metric units.
- Pick a wheel and surface, or choose to enter your own coefficient.
- Enter the mass, and a speed if you want the power.
- Press Calculate.
The basic formula
The rolling resistance is the coefficient times the normal force N, the vertical weight of the object. Wikipedia writes this with the symbol Crr: F = Crr × N [1]. On level ground the normal force equals the weight, which is the vehicle mass times the acceleration of gravity. We use 9.80665 m/s², the standard value [3].
Weight and the normal force
The calculator turns the mass into newtons by multiplying by 9.80665 m/s². In US units the mass is in pounds, and the pound is defined as exactly 0.45359237 kg [2]. A pound-force is that mass times standard gravity, which is about 4.4482216 newtons [2]. As a result, a vehicle of 2,000 lb on level ground with a coefficient of 0.01 has a rolling resistance of exactly 20 lbf, or about 88.96 N.
Typical coefficients
Wikipedia lists coefficients for common cases [1]. A steel railroad wheel on a steel rail is 0.0003 to 0.0004, and production bicycle tyres at 120 psi are 0.0022 to 0.0050. Large truck tyres are 0.0045 to 0.0080, car tyre measurements span 0.0062 to 0.0150, and ordinary car tyres on concrete are 0.0100 to 0.0150. Ordinary car tyres on sand reach 0.3000 [1]. For a range, the tool shows the force at both ends.
A worked example
A 1,000 kg car with a coefficient of 0.015 has a normal force of 1,000 × 9.80665 = 9,806.65 N and a rolling resistance of 147.1 N. Using g = 9.81 m/s² instead gives about 147 N, so the small difference comes from the value of g. At 90 km/h, which is 25 m/s, the power needed against rolling resistance is about 3,677 W, from P = F × v.
Power and speed
Wikipedia states that power is force times velocity [1]. The calculator converts your speed to metres per second: one mile per hour is 0.44704 m/s exactly, and a kilometre per hour is one 3.6th of a metre per second. The result is given in watts and kilowatts. It covers only the rolling part, so drag, hills and drivetrain losses all come on top.
Why the coefficient is hard to pin down
The coefficient is hard to pin down, because it can change with speed, pressure and temperature. Wikipedia adds that rolling resistance generally falls as the tyre warms up within a limited range, with one source showing a 20 to 25 percent reduction from 30 °C to 70 °C [1]. For railroad bearings it also varies with speed and load [1]. Treat any single value as a typical figure.
Rolling resistance and size
Wikipedia gives the force as the coefficient times the normal force, so it grows with the vehicle weight [1]. For pneumatic tyres on hard pavement, Wikipedia reports that the effect of wheel diameter is negligible within a practical range [1]. Doubling the mass doubles the force for the same coefficient, which is why heavy loads and soft surfaces such as sand have such a large effect on fuel use.
Rolling resistance and drag
The tool looks only at rolling resistance and leaves out aerodynamic drag, which grows with speed, so add a drag calculation for the full picture. It is a good first estimate for slow vehicles, trolleys and rail wagons.
What the tool assumes
The presets use the Wikipedia table of coefficients [1], and the power is P = F v, force times velocity [1]. We assume level ground and a steady speed, and ignore slip and applied torque, which Wikipedia notes can raise rolling resistance far above its basic value [1].
Using the calculator
Pick the units first. Choose a wheel and surface from the list, or choose to enter your own coefficient from a tyre label or test. Enter the mass, add a speed if you want the power, and press Calculate. Compare presets to see how much a soft surface or a different tyre changes the force, and remember to use the loaded mass of the vehicle with passengers and cargo.
Comparing vehicles and surfaces
Because the formula is linear, you can compare cases quickly. A steel wheel on a rail needs a small fraction of the force of a car tyre on concrete for the same weight, using the Wikipedia ranges [1]. A tyre on sand needs more than twenty times as much force as on concrete. Pick two presets in turn and read the force and the power to see what a change of surface or wheel is worth.
Common mistakes
- Using weight instead of mass. Enter the mass; the tool applies gravity.
- Using a coefficient for the wrong surface. Sand is far higher than concrete.
- Forgetting speed effects. The coefficient can change with speed and temperature.
- Assuming a slope of zero. Hills add a force that this tool does not include.
What next
Use this often? Add Rolling Resi to your Home screen.
Frequently asked questions
What is a rolling resistance calculator?
A tool that finds the force opposing a rolling wheel from the vehicle mass and the rolling resistance coefficient, and the power needed to overcome it.
What is the rolling resistance formula?
F = Crr × N, where N is the normal force, which equals the weight on level ground.
What is a typical rolling resistance coefficient for a car tyre?
Wikipedia lists about 0.0100 to 0.0150 for ordinary car tyres on concrete.
How do I calculate the power needed?
Multiply the rolling resistance force by the speed in metres per second.
Does tyre size change rolling resistance?
Wikipedia reports that the effect of wheel diameter on pneumatic tyres is negligible within a practical range, but it does depend on the vehicle weight.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.