A drag equation calculator finds the drag force on a body that moves through a fluid such as air or water, and the power needed to overcome it, from the speed, the drag coefficient and the frontal area. It also finds the terminal velocity of a falling body from its mass.
How to use the drag equation calculator
- Choose US or metric units.
- Enter the speed, drag coefficient and frontal area.
- Add a mass for the terminal velocity.
- Press Calculate.
The drag equation
The drag force on a body in a fluid is F_D = ½ ρ v² C_D A, where ρ is the density of the fluid, v the speed relative to the fluid, C_D the dimensionless drag coefficient and A the cross-sectional, or frontal, area [1]. The force grows with the square of the speed: doubling the speed quadruples the drag. It also grows with the density of the fluid, which is why drag in water is far greater than in air.
Power
The power needed to overcome the drag is P_D = F_D v = ½ ρ v³ A C_D [1]. The page says that the power varies as the square of the speed at low Reynolds numbers, and as the cube of the speed at high ones [1]. It gives an example: a car at 50 miles per hour needs about 10 horsepower to overcome drag, and at 100 miles per hour about 80 horsepower [1]. That is eight times as much for twice the speed.
The air density
The calculator uses 1.204 kilograms per cubic metre for air, the value that the page on density gives for 20 degrees Celsius at 1 atmosphere [3]. For a colder day, the density is higher: 1.293 at 0 degrees [3]. Enter another density for water, which is about 1,000, or for air at altitude. The density of air can also be found with the air density calculator on this site.
The drag coefficient
The drag coefficient depends on the shape and the surface of the body, and on the Reynolds number. The pages that we read give no table of values, so we cannot quote them. Look up the coefficient for your object, from the maker or from a handbook. Smooth, streamlined shapes have small coefficients, and flat or blunt ones large coefficients, close to 1 or more.
A worked example
For a car with a drag coefficient of 0.3 and a frontal area of 2.2 square metres, at 100 kilometres per hour, which is 27.78 metres per second, the drag is 306.6 newtons, which is 68.9 pounds-force. The power is 8.52 kilowatts, 11.4 horsepower. These are our own calculations, with the numbers chosen for the example, and are not those of a particular car.
Terminal velocity
A body that falls through a fluid speeds up until the drag balances its weight. The terminal velocity is then v_t = √(2 m g ÷ (ρ A C_D)) [2]. The page notes that an object approaches its terminal speed asymptotically [2]. The calculator uses g = 9.80665 metres per second squared. A falling body of 80 kilograms with C_D = 1 and A = 0.7 square metres reaches 43.1 metres per second.
Skydivers
The page gives some examples. A skydiver in a belly-to-earth position falls at about 55 metres per second, with the limbs pulled in about 90 metres per second, and a head-down competitor can reach 150 metres per second [2]. These speeds differ because the area and the drag coefficient differ. Enter a mass and a plausible area and coefficient to see how the terminal velocity changes with posture.
Speeding up
The page also says that a skydiver in free fall reaches half of the terminal speed after about 3 seconds, 90 percent after 8 seconds and 99 percent after 15 seconds [2]. The velocity over time follows v(t) = v_t tanh(g t ÷ v_t) [2]. The calculator gives the terminal speed only, but you can use the formula with it to see how the speed builds up.
Units
In US mode, the speed is in miles per hour, the area in square feet and the mass in pounds. In metric mode, the speed is in kilometres per hour, the area in square metres and the mass in kilograms. The results are shown in newtons and pounds-force, and in watts and horsepower. The terminal velocity is in metres per second, kilometres per hour and miles per hour.
Limits
The equation is for turbulent flow at high Reynolds numbers, where the drag goes as the square of the speed. At very low speeds, or for very small particles, the drag is proportional to the speed, and the Stokes formula applies, which the page also gives [2]. The calculator assumes a constant drag coefficient, which is a good approximation over a modest range of speeds.
Using the calculator
Pick the units. Enter the speed, the drag coefficient and the area, and read the force and the power. Change the speed to see the cube law for power. Add a mass to find a terminal velocity, and compare postures or shapes by changing the area and the coefficient. Remember that the real drag also includes the wind: use the speed relative to the air.
Comparing speeds
For the car of the example, the drag power is 1.07 kilowatts at 50 kilometres per hour, 8.52 kilowatts at 100 and 28.7 kilowatts at 150. The last figure is 27 times the first, since 150 is three times 50 and three cubed is 27. At motorway speeds, drag is the largest load on the engine, which is why fuel use rises quickly with speed. These are our own calculations.
Common mistakes
- Using the ground speed in a wind. Use the speed relative to the air.
- Taking the wrong area. Use the frontal area.
- Using the same coefficient at all speeds. It can change.
- Forgetting that power grows with the cube. Double the speed means eight times the power.
What next
Use this often? Add Drag Equatio to your Home screen.
Frequently asked questions
What is a drag equation calculator?
A tool that finds the drag force on a body moving through a fluid.
What is the drag equation?
F_D = ½ ρ v² C_D A.
How does power depend on speed?
P = F_D v, which grows with the cube of the speed at high Reynolds numbers.
What is the terminal velocity formula?
v_t = √(2 m g ÷ (ρ A C_D)).
What is the terminal speed of a skydiver belly-down?
About 55 m/s.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.