An air density calculator finds the density of air from its temperature, pressure and relative humidity. Enter the three values, in US or metric units, and it gives the density in kilograms per cubic metre and in pounds per cubic foot, and compares it with the standard atmosphere.
How to use the air density calculator
- Choose US or metric units.
- Enter the temperature and the pressure.
- Add the relative humidity if you know it.
- Press Calculate.
The ideal gas law
The density of dry air follows from the ideal gas law, ρ = p ÷ (R T), where p is the absolute pressure, T the absolute temperature in kelvin and R the specific gas constant [1]. For dry air, the page gives R as 287.058 joules per kilogram kelvin [1]. The calculator converts the temperature to kelvin, and the pressure to pascals, before it applies the law.
Check against the page
At 20 degrees Celsius and 101,325 pascals, the density of dry air is 1.2041 kilograms per cubic metre [1]. The calculator gives the same result. At 15 degrees Celsius and the same pressure, the figure for the International Standard Atmosphere, it gives 1.2250 [1]. The result is also shown as a percentage of this standard value, so you can see at a glance whether the air is thinner or denser.
Humid air
Moist air is lighter than dry air, because water vapour, with a specific gas constant of 461.495 joules per kilogram kelvin [1], is less dense than the nitrogen and oxygen that it displaces. The density is the sum of the dry air part and the vapour part: ρ = p_d ÷ (R_d T) + p_v ÷ (R_v T), where p_v is the partial pressure of the vapour and p_d is the total pressure less p_v [1].
Vapour pressure
The partial pressure of the vapour is the relative humidity times the saturation vapour pressure. The calculator estimates the saturation pressure with the Tetens formula, 6.1078 × 10 raised to 7.5 T ÷ (T + 237.3) in hectopascals, with T in degrees Celsius. This is the common form of that approximation, and the constants are our own working, so treat it as an estimate. At 20 degrees and 50 percent humidity, p_v is 11.69 hectopascals and the density is 1.1988.
Temperature and pressure
Warmer air is less dense, and so is air at a lower pressure. At 30 degrees Celsius, dry air at standard pressure has a density of 1.1644 kilograms per cubic metre, and at 0 degrees it has 1.2922. At a pressure of 900 hectopascals, as at an altitude of about 1,000 metres, the density at 15 degrees is 1.0881. These are our own calculations from the formula.
Why it matters
Air density changes the lift of wings and rotors, the drag on cars and cyclists, the power of an engine that breathes air, and the performance of a ball in flight. Pilots use density altitude to judge how an aircraft will perform on a hot day. Engineers use the density to size fans and to convert between mass flow and volume flow.
Pressure to use
Use the pressure at your own location, which is the station pressure. Weather reports usually give the pressure adjusted to sea level, which is higher than the pressure at a place above sea level. If you only know the sea-level value, the density will be too high for a place at altitude. For a standard value, 29.92 inches of mercury or 1,013.25 hectopascals is the pressure at sea level.
Units
In US mode, the temperature is in degrees Fahrenheit and the pressure in inches of mercury, where one inch is about 33.8639 hectopascals. In metric mode, it is degrees Celsius and hectopascals. The result is given in kilograms per cubic metre and in pounds per cubic foot. One kilogram per cubic metre is 0.06243 pounds per cubic foot.
Using the calculator
Enter the values for the place and the day, with the humidity if you have it. Compare the result with the standard value of 1.2250, which the line below it shows as a percentage. A result under 100 percent means thinner air than the standard atmosphere. Check the working line for the temperature in kelvin and the pressure that were used.
A hot, humid example
On a hot, humid day at 35 degrees Celsius and 60 percent humidity, the vapour pressure is 33.7 hectopascals and the air density at standard pressure is 1.1311 kilograms per cubic metre, about 92 percent of the standard value. The dry figure for the same temperature and pressure is 1.1455. Hot and humid air is therefore noticeably thinner, which is why aircraft need longer runways on such days. This is our own calculation.
Accuracy
The ideal gas law is very accurate for air at everyday temperatures and pressures, so the main source of error is in the inputs. A temperature that is off by 3 degrees changes the density by about 1 percent, and a pressure error of 10 hectopascals changes it by about 1 percent as well. Read the temperature in the shade, away from heat, and use a recent pressure reading from your own location.
Common mistakes
- Using sea-level pressure at altitude. Use the station pressure.
- Entering the temperature in the wrong unit. Check the units setting.
- Forgetting humidity. Moist air is lighter.
- Using gauge pressure. Use the absolute pressure.
What next
Use this often? Add Air Density to your Home screen.
Frequently asked questions
What is an air density calculator?
A tool that finds the density of air from its temperature, pressure and humidity.
What is the density of air at 20 °C?
About 1.2041 kg/m³ for dry air at 101,325 Pa.
What is the formula for air density?
ρ = p ÷ (R T), with R = 287.058 J/(kg·K) for dry air.
Is humid air denser than dry air?
No. Moist air is lighter, because water vapour is less dense than air.
What is the density of the standard atmosphere?
1.2250 kg/m³ at 15 °C and 101,325 Pa.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.