Saved

Press the star next to a tool's name to save it.

All my tools

Friction Force Calculator

Use this friction force calculator to find the static and kinetic friction on an object from its mass and the coefficients of friction, on a flat surface or a slope, and test a push.

Restored your last values ·

Choose US or metric units. Enter the mass of the object and the coefficients of friction of the two surfaces. Add a slope angle for a ramp, and a push to see whether the object moves.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the mass and the coefficient of friction, then press Calculate.

See full result

A friction force calculator finds the friction between an object and a surface from its mass and the coefficient of friction. It gives the maximum static friction and the kinetic friction, handles a slope or a ramp, and can tell you whether a given push will make the object move or whether it will slide down.

How to use the friction force calculator

  1. Choose US or metric units.
  2. Enter the mass and the coefficients of friction.
  3. Add a slope angle or a push if you want.
  4. Press Calculate.

The friction laws

The friction between two dry surfaces follows simple laws. The static friction force can take any value up to a maximum: F_f ≤ μ_s N, where N is the normal force that presses the surfaces together [1]. Once the object slides, the kinetic friction is F_k = μ_k N [1]. The coefficient of kinetic friction is usually a little lower than the static one. We read these formulas in a summary form of the page, and they are the standard laws.

The normal force

On a flat surface, the normal force equals the weight, N = m g, where g = 9.80665 metres per second squared. On a slope of angle θ, it is N = m g cos θ, which is less. A 10 kilogram object has a normal force of 98.07 newtons on a flat surface. The calculator takes the weight from the mass that you enter, in pounds or kilograms.

A worked example

For a mass of 10 kilograms and a coefficient of static friction of 0.74, the maximum static friction is 72.57 newtons. With a kinetic coefficient of 0.42, the friction while sliding is 41.19 newtons. The coefficients are in the range that the page gives for steel on steel: 0.74 to 0.80 static and about 0.42 for kinetic [1], which we read only in a summary of the table, so check them in a handbook.

Does it move?

Enter a push along the surface to see whether the object starts to move. The push must exceed the maximum static friction, plus the pull of gravity along a slope. A push of 60 newtons on the 10 kilogram object with a coefficient of 0.5, whose maximum friction is 49 newtons, makes it move. A push of 20 newtons does not: the friction then just matches the push.

After it starts

Once the object moves, the friction drops to the kinetic value, and the net force is the push minus the friction. With a kinetic coefficient of 0.3, the friction is 29.4 newtons, and the net force on the 10 kilogram object is 30.6 newtons, so it speeds up at 3.06 metres per second squared. The calculator gives the acceleration if you enter both the push and the kinetic coefficient.

The angle of repose

On a slope, gravity pulls the object down with m g sin θ. The object stays at rest as long as this is less than the maximum static friction, μ_s m g cos θ. This gives the condition tan θ < μ_s. The angle of repose is therefore arctan μ_s [1]. For a coefficient of 0.74, it is 36.5 degrees. The calculator gives this angle and says whether your slope is above it.

A slope example

A 10 kilogram block on a slope of 20 degrees with a coefficient of 0.5 has a normal force of 92.15 newtons. Gravity pulls it down the slope with 33.54 newtons, while the static friction can give 46.08 newtons. So it stays put. With a coefficient of 0.3, the maximum friction is 27.65 newtons and it slides, with kinetic friction of 18.43 newtons if μ_k is 0.2. These are our own calculations.

Coefficients of friction

Coefficients depend greatly on the materials. The page has a table for many pairs, such as steel on steel, rubber on concrete and ice on ice, with ranges that depend on whether the surfaces are dry or wet [1]. We cannot give them with confidence, because we could not read the table in full, so the calculator asks for the coefficient. Use values from your own data.

Units

In US mode, the mass is in pounds and the push in pounds-force. In metric mode, they are in kilograms and newtons. The friction forces are given in newtons and pounds-force. The angle is in degrees from the horizontal. Leave the angle blank for a flat surface. The coefficients are dimensionless numbers, usually between about 0.03 and 1.

Limits

The simple laws are approximate. Friction depends on the temperature, the speed, the roughness and any contaminants, and for rubber it can exceed 1. The laws also assume that the friction does not depend on the contact area, which is a good approximation for hard dry surfaces. For a design where safety matters, test the real surfaces.

Using the calculator

Enter the mass and the static coefficient, and the kinetic one if you know it. Read the maximum friction and the kinetic friction. Add a slope or a push to see what happens. Try several coefficients to see how sensitive the result is, and remember that wet or oily surfaces can have much lower coefficients than dry ones.

Common mistakes

  • Using the kinetic coefficient for starting. Starting uses the static value.
  • Forgetting the cosine on a slope. N is less on a slope.
  • Mixing pounds and kilograms. Check the units.
  • Using a dry coefficient for a wet surface. It is much lower.

What next

Use this often? Add Friction For to your Home screen.

Frequently asked questions

What is a friction force calculator?

A tool that finds the friction on an object from its mass and the coefficient of friction.

What is the friction formula?

F_f ≤ μ_s N for static friction and F_k = μ_k N for sliding.

What is the normal force on a slope?

N = m g cos θ.

What is the angle of repose?

arctan μ_s, the steepest slope on which the object stays at rest.

Is kinetic friction less than static friction?

Usually, yes.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools