Saved

Press the star next to a tool's name to save it.

All my tools

Rolling Offset Calculator

Use this rolling offset calculator to work out the true offset, travel, run and cut length for a pipe offset that rises and rolls at once, with 45°, 22½° or other fittings.

Restored your last values ·

Set is how far the pipe moves up or down; roll is how far it moves sideways. Measure center to center. Take-off is the fitting's center-to-end allowance, from the maker.

Everything is worked out in your browser. Nothing you type is sent anywhere.

Travel (center to center)

–

Enter the set and roll, then press Calculate.

See full result

This rolling offset calculator works out the travel, run and cut length of a pipe that changes direction both up or down and sideways at once. Enter the set (rise), the roll and the fitting angle, and the rolling offset calculator gives the true offset, the travel between fitting centers, the run, and the cut length once you subtract the fitting take-offs.

How to use the rolling offset calculator

  1. Choose inches or millimeters.
  2. Choose the fitting angle: 45°, 22½°, 60°, 30° or 11¼°.
  3. Enter the set, the vertical change, and the roll, the sideways change, measured center to center.
  4. Enter the fitting take-off if you want the cut length, then press Calculate.

What is a rolling offset?

A simple offset moves a pipe sideways in one plane, using two angled fittings. A rolling offset moves it in two directions at once: up or down (the set) and sideways (the roll). Looking along the pipe, the two changes form the two short sides of a right triangle, and the pipe's actual offset is the diagonal between them.

The true offset

By the Pythagorean theorem, the square of the hypotenuse equals the sum of the squares of the other two sides (a² + b² = c²). So the true offset is:

true offset = √(set² + roll²)

Once you have the true offset, a rolling offset is worked out just like a simple offset in that diagonal plane.

Travel and run

The travel is the center-to-center length of the angled piece of pipe, and the run (or advance) is how far the offset moves along the line of the pipe. With fittings of angle θ:

  • Travel = true offset ÷ sin θ
  • Run = true offset ÷ tan θ

These give the familiar constants: for 45° fittings, travel = true offset × 1.414 and run = true offset × 1; for 22½°, travel × 2.613 and run × 2.414; for 60°, travel × 1.155 and run × 0.577. The Wikipedia article on piping and plumbing fittings notes that elbows usually come in 90° and 45°, and that 22.5° elbows are also available.

Worked example

A pipe needs to rise 12 inches and roll 9 inches, using 45° fittings. The true offset is √(12² + 9²) = √225 = 15 inches. The travel is 15 × 1.414 = 21.21 inches, and the run is 15 inches. With 22½° fittings, a set of 24 inches and a roll of 10 inches give a true offset of 26 inches, a travel of 67.94 inches and a run of 62.77 inches.

Cut length

The travel is measured between fitting centers. The pipe itself is shorter, because part of the distance is taken up inside each fitting. Subtract the take-off, the distance from each fitting's center to the end of the pipe in it, for both fittings: cut length = travel − 2 × take-off. Take-offs depend on the fitting type and size, so use the manufacturer's figures.

Reading the results

The big number is the travel, center to center. The table shows the true offset, the run, the cut length if you entered a take-off, and the travel and run constants for the fitting angle you chose.

Simple offsets

The same calculator handles a simple offset, where the pipe moves in only one direction. Enter the offset as the set and leave the roll at 0: the true offset is then just the set, and the travel and run follow from the fitting angle. For example, a 10-inch simple offset with 45° fittings has a travel of 14.14 inches and a run of 10 inches.

Choosing a fitting angle

Steeper fittings make a shorter, more compact offset, while shallower fittings stretch it out along the pipe. For a 15-inch true offset, 60° fittings need a travel of 17.32 inches and a run of 8.66 inches; 45° fittings need 21.21 and 15 inches; and 22½° fittings need 39.20 and 36.21 inches. Choose the angle that fits the space and the fittings you have, and remember that gentler bends usually let fluid flow more smoothly.

Measuring set and roll

Measure the set as the vertical distance between the centerlines of the two pipes, and the roll as the horizontal distance between them, square to the run of the pipe. A level and a square help: mark both centerlines on a wall or framing, then measure straight up and straight across. Small errors add up, so measure twice before cutting.

Metric piping

Choose millimeters to work in metric. The constants are the same in any unit, because they come from the fitting angle, so a 300 mm set and 400 mm roll with 45° fittings give a 500 mm true offset and a travel of about 707 mm.

Checking your work

After a dry fit, measure the actual set and roll again before you glue, solder or weld. If they don't match, adjust the cut length rather than forcing the fittings, which can strain the joints.

Common mistakes

  • Adding set and roll. Use the square root of their squares, not their sum.
  • Measuring to pipe edges. Measure center to center.
  • Cutting to travel. Subtract both take-offs.
  • Mixing fitting angles. Both fittings in an offset should be the same angle.

Tips

  • Draw a quick sketch of set, roll and run before you measure.
  • Check with a tape on a dry fit before gluing or welding.
  • Keep a list of take-offs for the fittings you use most.

What next

Use this often? Add Rolling Offs to your Home screen.

Frequently asked questions

How does a rolling offset calculator work?

It finds the true offset with √(set² + roll²), then travel = true offset ÷ sin(angle) and run = true offset ÷ tan(angle).

What is the formula for a 45° rolling offset?

Travel = √(set² + roll²) × 1.414.

What is the 22½° offset constant?

Travel is 2.613 times the true offset, and the run is 2.414 times.

How do I find the cut length?

Subtract twice the fitting take-off from the center-to-center travel.

What is the difference between set and roll?

Set is the vertical change and roll is the sideways change.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools