Saved

Press the star next to a tool's name to save it.

All my tools

Gallons per Minute Calculator

Use this gallons per minute calculator to work out water flow rate in GPM and liters per minute from a bucket test or a pipe's size and flow speed.

Restored your last values ·

For a quick test at home, time how long a faucet or hose takes to fill a bucket of known size.

Everything is worked out in your browser. Nothing you type is sent anywhere.

Flow rate

–

Enter your measurements, then press Calculate.

See full result

This gallons per minute calculator works out a water flow rate in gallons per minute (GPM), from a simple bucket test or from a pipe's size and flow speed. Enter how much water you collected and how long it took, or the pipe's inside diameter and the velocity, and the gallons per minute calculator gives the flow in GPM and liters per minute, plus gallons per hour and cubic feet per second.

How to use the gallons per minute calculator

  1. Choose US or metric units. US (gallons, inches and feet per second) is the default.
  2. Choose how you measured: a container and stopwatch, or the pipe size and speed.
  3. Enter your measurements.
  4. Press Calculate.

What is flow rate?

Wikipedia defines volumetric flow rate as the volume of fluid that passes per unit of time. In US customary units it's often given in gallons per minute or cubic feet per second; in metric, in liters per minute or cubic meters per second. Knowing the flow rate of a faucet, hose, well pump or irrigation line helps you size pipes, sprinklers and pumps, or check whether a fixture is working properly.

The bucket method

The simplest way to measure flow is to fill a container of known size and time it. Flow rate is then the volume divided by the time:

GPM = gallons collected ÷ (seconds ÷ 60)

For example, a 5-gallon bucket that fills in 30 seconds means 5 ÷ 0.5 = 10 GPM, or about 37.9 liters per minute.

The pipe method

Wikipedia also gives flow rate as the flow velocity times the cross-sectional area, Q = v × A, for flow that's uniform across a flat cross-section. A pipe's area is π × (diameter ÷ 2)². The calculator works out the area from the inside diameter, multiplies by the velocity, and converts the result to gallons and liters per minute.

Worked example

Take a pipe with a 1-inch inside diameter and water moving at 5 feet per second. The area is π × 0.5² = 0.785 square inches, or about 0.00545 square feet. At 5 ft/s, that's 0.0273 cubic feet per second, which is about 12.2 GPM. In metric, a 50 mm pipe at 1.5 m/s carries about 177 liters per minute.

Gallons and liters

The calculator uses the US gallon, which is exactly 3.785411784 liters (231 cubic inches). The imperial gallon used in the UK is larger, about 4.546 liters, so if your container is marked in imperial gallons, convert it to liters and use metric. One cubic foot is about 7.48 US gallons.

Reading the results

The big number is the flow rate in GPM (or liters per minute in metric). The table shows the same flow in the other unit, in gallons per hour and in cubic feet per second.

Getting a good measurement

For a bucket test, use the largest container you can and open the tap fully before you start timing, then move the container under the stream as you start the stopwatch. Repeat the test two or three times and average the results. For the pipe method, remember that real flow is faster in the middle of a pipe than near the walls, so an average velocity gives the best estimate.

Typical uses

Flow rate matters whenever water has to move a certain amount in a certain time. A garden irrigation system needs enough GPM to run all the sprinklers on a zone at once. A well pump is chosen to deliver the household's peak flow. A water heater or filter has a maximum flow rate it can handle. Measuring the actual flow at your tap or hose tells you what you have to work with.

Pipe size and velocity

Because flow equals area times velocity, a bigger pipe carries more water at the same speed: doubling the inside diameter quadruples the area and the flow. For the same flow, water moves faster in a smaller pipe. In the example, a 1-inch pipe carries about 12.2 GPM at 5 feet per second; a 2-inch pipe at the same speed carries about 49 GPM.

Liters per minute

Choose metric to enter liters, millimeters and meters per second, and see the flow in liters per minute first. The same bucket test works in liters: a 10-liter bucket filling in 30 seconds is 20 liters per minute, about 5.3 GPM.

Converting between units

The table converts the flow for you. To go from GPM to gallons per hour, multiply by 60; from GPM to cubic feet per second, divide by about 448.8. A flow of 10 GPM is 600 gallons per hour, about 0.0223 cubic feet per second.

Common mistakes

  • Using the outside diameter. Use the pipe's inside diameter.
  • Mixing gallon types. The calculator uses US gallons.
  • Timing too short. Fill times under a few seconds are hard to measure.
  • Partly closed taps. Open the tap fully for a maximum flow test.

Tips

  • Mark your bucket at a known volume for repeat tests.
  • Test at the same time of day to compare.
  • Check flow at the furthest outlet when sizing pumps.

What next

Use this often? Add Gallons per to your Home screen.

Frequently asked questions

How does a gallons per minute calculator work?

It divides the volume of water by the time it took, or multiplies a pipe's area by the flow velocity.

How do I measure GPM with a bucket?

Time how long a bucket of known size takes to fill: a 5-gallon bucket in 30 seconds is 10 GPM.

How many GPM through a 1-inch pipe?

About 12.2 GPM at 5 feet per second.

How do I convert GPM to liters per minute?

Multiply by 3.785411784, the liters in a US gallon.

What is the formula for flow rate in a pipe?

Q = v × A: flow velocity times the pipe's cross-sectional area.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools