An RLC circuit calculator finds how a resistor, an inductor and a capacitor behave together. Enter the three values for a series or a parallel circuit and it gives the resonant frequency, the quality factor Q, the bandwidth and the damping. Add a frequency and it also works as an RLC impedance calculator, with the impedance and the phase angle.
How to use the RLC circuit calculator
- Choose a series or a parallel circuit.
- Enter the resistance in ohms and pick the units for the inductance and the capacitance.
- Optionally add a frequency in hertz to get the impedance.
- Press Calculate.
Resonant frequency
The resonant frequency of the series circuit is ω₀ = 1 ÷ √(LC), or f = 1 ÷ (2π√(LC)), which depends only on the inductance and the capacitance, not on the resistance [1]. The parallel circuit has the same resonant frequency [1]. For example, a 25 mH coil and a 50 µF capacitor resonate at about 142.35 Hz, and a 1 µH coil with a 2 pF capacitor resonates at about 112.54 MHz.
Quality factor Q
For the series circuit the quality factor is Q = (1 ÷ R)√(L ÷ C) [1]. With R = 30 Ω, L = 25 mH and C = 50 µF it comes to about 0.7454. The parallel circuit has the reciprocal form Q = R√(C ÷ L) [1]. A higher Q means a sharper, more selective resonance with a narrower bandwidth [1]. In a series circuit you raise Q by lowering R, or by raising L while lowering C, which follows from the formula.
Bandwidth
The width of the resonance is linked to Q. Wikipedia gives Q = ω₀ ÷ Δω for the series circuit, so the bandwidth is the resonant frequency divided by Q [1]. We apply the same definition to the parallel circuit, which is our own working. With a Q of 0.7454 at 142.35 Hz the bandwidth is about 190.99 Hz, a wide, low-Q resonance. A circuit with Q = 50 at 1 MHz has a bandwidth of only 20 kHz.
Damping ratio and damping rate
The damping ratio is ζ = 1 ÷ (2Q), and the damping rate is α = R ÷ (2L) for a series circuit or 1 ÷ (2RC) for a parallel one [1]. When ζ is below 1 the response is a decaying oscillation at ω_d = ω₀√(1 − ζ²). When ζ equals 1 it is critically damped, and above 1 it is overdamped with no oscillation [1]. A Q below one half means a damping ratio above 1, so the circuit is overdamped and does not oscillate [1].
RLC impedance
Add a frequency and the tool works as an RLC impedance calculator. With ω = 2πf, the series impedance is Z = √(R² + (ωL − 1 ÷ (ωC))²), the magnitude of R + jX with X = ωL − 1 ÷ (ωC) [2]. For the parallel circuit the admittances add, 1 ÷ Z = 1 ÷ R + 1 ÷ (jωL) + jωC [1], so Z = 1 ÷ √(1 ÷ R² + (1 ÷ (ωL) − ωC)²). Series impedance is smallest at resonance, where it equals R, while parallel impedance is largest at resonance [1].
Phase angle
The phase is φ = arctan((ωL − 1 ÷ (ωC)) ÷ R) for the series circuit and φ = arctan(R(1 ÷ (ωL) − ωC)) for the parallel one, which is the phase angle arctan(X ÷ R) of the impedance [2]. A positive phase means that the voltage leads the current, and a negative phase that it lags. The calculator labels the result inductive, capacitive or resistive so you do not need to remember the sign convention.
A parallel worked example
Take a parallel circuit with R = 10 Ω, L = 2 mH, C = 500 µF and f = 1 kHz. The impedance is about 0.326 Ω: the calculator gives 0.32641 Ω with a phase of about −88.13°, so the circuit is strongly capacitive at that frequency.
What the calculator assumes
The resonance, Q and damping results above follow the Wikipedia article [1]. The bandwidth rule is applied to the parallel circuit as our own working. The calculator assumes ideal parts, a sinusoidal drive and a single resonance, so measure real circuits before relying on a design.
Choosing units
Inductance can be entered in microhenries, millihenries or henries, and capacitance in picofarads, nanofarads, microfarads or farads. The tool converts them into henries and farads before it works. A common slip is to enter a value in microfarads while the unit box says millifarads or farads, which changes the resonant frequency by a factor of thousands. Check the placeholders and the units shown in the working line.
Series and parallel compared
The two circuits look alike on paper but behave in opposite ways. A series circuit has its lowest impedance at resonance, where the impedance equals the resistance, so it passes the signal best at that frequency [2]. A parallel circuit has its highest impedance at resonance and is called an antiresonator [1]. That is why series circuits suit tuned receivers and filters that pass a band, while parallel circuits suit traps that block one.
Using the RLC impedance result
Enter a frequency below, at and above the resonant frequency and watch how the phase changes sign. Below resonance a series circuit is capacitive, and above it the coil dominates and it turns inductive. The impedance value is the total opposition to the alternating current in ohms, so divide the supply voltage by it to estimate the current.
Common mistakes
- Mixing up series and parallel. The Q formulas are reciprocals of each other.
- Entering the capacitance in the wrong unit. Pick µF, nF or pF to match your part.
- Expecting the resonance to depend on R. Only L and C set the frequency.
- Ignoring coil resistance. Real coils add series resistance and lower Q.
What next
Use this often? Add RLC Circuit to your Home screen.
Frequently asked questions
What is an RLC circuit calculator?
A tool that finds the resonant frequency, Q factor, bandwidth, damping and impedance of a circuit built from a resistor, an inductor and a capacitor.
What is the resonant frequency of an RLC circuit?
f = 1 ÷ (2π√(LC)), which does not depend on the resistance.
How do you calculate RLC impedance?
With ω = 2πf, the series impedance is the square root of R² plus (ωL − 1 ÷ ωC)². The parallel form uses admittances. Enter a frequency to get both the value and the phase.
What is the Q factor of a series RLC circuit?
Q = (1 ÷ R)√(L ÷ C). A parallel circuit uses the reciprocal, R√(C ÷ L).
When is an RLC circuit overdamped?
When the damping ratio ζ = 1 ÷ (2Q) is above 1, that is, Q below one half.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.