An RC cutoff frequency calculator finds the cutoff frequency and the time constant of a filter made from a resistor and a capacitor. Enter the resistance and the capacitance, and it gives the frequency at which the output is down by 3 dB. Add a test frequency to see the gain of the filter there.
How to use the RC cutoff frequency calculator
- Enter the resistance and the capacitance with their units.
- Add a test frequency for the gain.
- Press Calculate.
The cutoff frequency
The cutoff frequency of an RC circuit is ω_c = 1 ÷ RC, or f_c = 1 ÷ (2π R C), the frequency at which the filter attenuates the signal to half its original power [1]. At this frequency the gain falls to 1 ÷ √2, about 0.707 [1]. The same frequency is the corner of both the low-pass and the high-pass filter that can be made from the two parts.
The −3 dB point
The page on the low-pass filter says that at the cutoff frequency the filter attenuates the input power by half, which is 3 dB [2]. A power ratio of one half is −3.01 dB, so the cutoff frequency is also called the −3 dB frequency. Below the cutoff, a low-pass filter passes the signal almost unchanged, and above it the signal falls off at 6 dB for each doubling of the frequency, a slope that is our own statement.
A worked example
A resistor of 1 kilohm with a capacitor of 1 microfarad has a time constant of 1 millisecond and a cutoff frequency of 159.15 hertz. With 10 kilohms and 0.1 microfarads, the cutoff is the same, since the product R C is the same. With 100 ohms and 10 nanofarads, τ is 1 microsecond, and the cutoff frequency is 159.15 kilohertz. These are our own calculations.
The time constant
The time constant is τ = R C [1]. The page says that it is the time that a discharging capacitor takes to fall to 1 ÷ e of its starting voltage [1]. It links the frequency and the time response: the cutoff frequency equals 1 ÷ (2π τ). A filter with a long time constant has a low cutoff, and responds slowly to a step.
Step response
The page also gives the response to a step. A capacitor charging through the resistor reaches about 63.2 percent of the final voltage after one time constant, and is often considered fully charged, to over 99.3 percent, after about five time constants [1]. For the 1 millisecond example, that is 5 milliseconds. The calculator shows the 5τ time in the working line.
Gain at a frequency
Enter a test frequency to see the gain of the low-pass version of the filter: gain = 1 ÷ √(1 + (f ÷ f_c)²). This is our own working from the circuit. At twice the cutoff, the gain is 0.4472, which is −6.99 dB. The high-pass gain at the same frequency is the complementary value, √(1 − gain²), and the calculator shows it as well.
Choosing the values
To design a filter for a cutoff frequency f_c, choose a convenient capacitor, and then find the resistor: R = 1 ÷ (2π f_c C). For 1 kilohertz with 100 nanofarads, R = 1,591.5 ohms. The source impedance adds to R, and the load can change the response, so use a buffer if you need a precise result. The calculator checks a pair of values.
Units
The resistance can be entered in ohms, kilohms or megohms, and the capacitance in picofarads, nanofarads, microfarads or millifarads. The frequency unit applies to the test frequency only. The results are shown in the most readable unit: hertz, kilohertz or megahertz for the cutoff, and seconds, milliseconds or microseconds for the time constant.
Limits
The formulas are for a first-order filter with an ideal source and no load. A filter that feeds a load, or is driven by a source with a high output resistance, has a different cutoff. Real capacitors have tolerances of 5 to 20 percent, and so do many resistors, which shifts the cutoff by a similar amount. For a steeper response, use a higher-order filter.
Using the calculator
Enter the resistance and the capacitance. Read the cutoff and the time constant. Enter a frequency to check how much of a signal passes. Swap the resistor and capacitor values to see that only the product matters. For a high-pass filter, the same cutoff applies, but the signal passes above it and not below.
Common pairs
A resistor of 10 kilohms with 100 nanofarads gives a cutoff of 159.15 hertz. 1 kilohm with 100 nanofarads gives 1.5915 kilohertz, and so do 10 kilohms with 10 nanofarads and 100 kilohms with 1 nanofarad. To cut off at 20 kilohertz, a common upper limit for audio, with a 10 nanofarad capacitor, the resistor is 796 ohms. These are our own calculations from the formula. Use them as starting points and check the result in the calculator.
Source and load effects
When the filter is driven by a source with its own output resistance, add that resistance to R. A source of 600 ohms with a 1 kilohm resistor behaves like 1.6 kilohms. In the same way, a load that draws current changes the response, and a buffer stage keeps the filter unaffected.
Common mistakes
- Using the wrong unit for the capacitor. Check pF, nF and µF.
- Forgetting the source resistance. It adds to R.
- Expecting a sharp cutoff. A first-order filter is gradual.
- Confusing τ with the cutoff frequency. f_c = 1 ÷ 2πτ.
What next
Use this often? Add RC Cutoff Fr to your Home screen.
Frequently asked questions
What is an RC cutoff frequency calculator?
A tool that finds the cutoff frequency of a resistor-capacitor filter.
What is the RC cutoff frequency formula?
f_c = 1 ÷ (2π R C).
What is the time constant of an RC circuit?
τ = R C.
What is the gain at the cutoff frequency?
1 ÷ √2, about 0.707, which is −3 dB.
Is the cutoff the same for high-pass and low-pass?
Yes, for the same R and C, the corner is at the same frequency.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.