A capacitive reactance calculator finds the reactance of a capacitor or an inductor at a given frequency. Enter the frequency and the capacitance or inductance, and it gives the reactance in ohms. Add a series resistance to get the impedance and the phase angle of an RC or RL circuit.
How to use the capacitive reactance calculator
- Choose a capacitor or an inductor.
- Enter the frequency and the component value with the right units.
- Add a series resistance if you want the impedance.
- Press Calculate.
Capacitive reactance
The reactance of a capacitor is X_C = −1 ÷ (ω C) = −1 ÷ (2π f C) [1]. The page gives the negative sign as one convention, and notes that it can also be defined as a positive number, X_C = 1 ÷ (2π f C), in which case the impedance is −jX_C [1]. The calculator shows the magnitude, and mentions the sign. Reactance is measured in ohms [1].
Frequency and capacitance
The reactance is inversely proportional to the frequency and to the capacitance [1]. At zero frequency, that is for direct current, its magnitude is infinite, so the capacitor acts like an open circuit. As the frequency goes to infinity, the reactance approaches zero, like a short circuit [1]. A 1 microfarad capacitor has a reactance of 159.15 ohms at 1 kilohertz, and 15.92 ohms at 10 kilohertz.
Inductive reactance
The reactance of an inductor is X_L = ω L = 2π f L [1]. It is proportional to the frequency and the inductance, so it is low at low frequencies and high at high ones, the opposite of a capacitor. An inductor of 10 millihenries has a reactance of 62.83 ohms at 1 kilohertz. At direct current it is zero, so an ideal inductor is like a short circuit.
Impedance
The impedance of a circuit is Z = R + jX, where R is the resistance and X the reactance, both in ohms [1]. A resistor of 100 ohms in series with a 1 microfarad capacitor at 1 kilohertz has a reactance of 159.15 ohms, so the size of the impedance is √(100² + 159.15²), which is 187.96 ohms. This magnitude and the angle are our own working, from the form on the page.
Phase
The page states that the voltage across a purely reactive device lags the current by π ÷ 2 for a capacitor, and leads it by π ÷ 2 for an inductor [1]. In the RC example, the angle of the impedance is −57.86 degrees, so the current leads the voltage by that angle. A pure reactance dissipates no power [1]. Only the resistor does, so a circuit with a large reactance can carry much current and yet use little energy.
Series reactances
For a capacitor and an inductor in series, the total reactance is X = X_L + X_C = ω L − 1 ÷ (ω C) [1]. If X is positive, the circuit is inductive. If it is zero, the circuit is purely resistive, which happens at the resonant frequency. If it is negative, the circuit is capacitive [1]. The calculator handles one component at a time, but you can add the results.
Units
Frequencies can be entered in hertz, kilohertz or megahertz, capacitances in picofarads, nanofarads, microfarads or millifarads, and inductances in microhenries, millihenries or henries. The calculator converts them to hertz, farads and henries. The working line shows the values in SI units. A capacitor of 100 picofarads at 1 megahertz has a reactance of 1,591.5 ohms.
Uses
Reactance is used to design filters, to match circuits, to size coupling and bypass capacitors and to choose chokes. A capacitor in series with a signal passes high frequencies, and an inductor in series passes low ones. By choosing the value so that the reactance is much smaller than the resistance at the frequency of interest, you can let the signal through.
Limits
Real capacitors and inductors depart from the ideal. A capacitor has a small series inductance and resistance, so its reactance does not keep falling at very high frequencies, and an inductor has a winding capacitance. The calculator gives the ideal value. The page also notes that for a square wave, the reactance of an inductor appears about 19 percent smaller than for a sine wave [1].
Using the calculator
Pick the component, enter the frequency with its unit and the value of the component. Read the reactance. To find a value for a given reactance, try a few values until the reactance matches. Add a resistor to see the impedance and the phase, and compare them for two or three frequencies to see how the circuit behaves.
Coupling and resonance
A coupling capacitor of 10 microfarads feeding a 10 kilohm load has a reactance of 795.8 ohms at 20 hertz, much smaller than the load, so it passes audio down to that frequency. An inductor of 10 millihenries and a capacitor of 1 microfarad have equal reactances of 100 ohms at 1,591.5 hertz, which is where they resonate, using f = 1 ÷ (2π √(LC)). The resonance formula is our own addition, and you can check the two reactances in the calculator.
Common mistakes
- Mixing microfarads and nanofarads. Check the unit.
- Using the frequency in hertz and the value in kilo-units. Match the units.
- Expecting reactance to dissipate power. Only resistance does.
- Using the formula for DC. Reactance applies to AC.
What next
Use this often? Add Capacitive R to your Home screen.
Frequently asked questions
What is a capacitive reactance calculator?
A tool that finds the reactance of a capacitor or an inductor at a frequency.
What is the formula for capacitive reactance?
X_C = 1 ÷ (2π f C), as a magnitude.
What is the formula for inductive reactance?
X_L = 2π f L.
What is the unit of reactance?
The ohm.
Does reactance use power?
No. A pure reactance dissipates no power.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.