A capacitor calculator works out the total capacitance of capacitors connected in parallel or in series, and how much charge and energy they store at a given voltage. Type the values with their units, such as 10u, 4.7n or 100p, choose how they're connected, and this capacitor calculator gives the combined value in the most readable unit. Add a voltage to see the charge (Q = CV) and the stored energy (½CV²), and add a resistor to get the RC time constant for charging and discharging.
Capacitors in parallel and in series
Capacitors combine the opposite way to resistors.
- In parallel, each capacitor adds to the total plate area, so the capacitances simply add: C = C₁ + C₂ + C₃ + …
- In series, the plate separation effectively adds up instead, so the reciprocals add: 1/C = 1/C₁ + 1/C₂ + 1/C₃ + …
A series string always has less capacitance than its smallest capacitor. Every capacitor in the string carries the same charge, and the total voltage is shared between them in inverse proportion to their capacitance, which is why capacitors are sometimes put in series to handle a higher working voltage.
Charge, energy and the farad
Capacitance is the ratio of the charge on each conductor to the voltage between them, C = Q / V. One farad means that one coulomb of charge produces one volt across the capacitor. Because a farad is a very large unit, everyday capacitors are measured in microfarads (µF), nanofarads (nF) and picofarads (pF).
The energy stored in a capacitor is W = ½CV². It's held in the electric field between the plates, and it grows with the square of the voltage, so doubling the voltage stores four times the energy.
The RC time constant
When a capacitor charges through a resistor, its voltage rises along a curve rather than jumping straight up. The time constant τ = RC sets the speed: after one time constant the capacitor reaches about 63% of the supply voltage, and the current and the voltage across the resistor fall away exponentially. After about five time constants it's considered fully charged for most practical purposes. Discharging works the same way in reverse.
Worked examples
Parallel. Three electrolytic capacitors of 10 µF, 22 µF and 47 µF are wired in parallel across a power rail. The total is 10 + 22 + 47 = 79 µF.
Series. The same three in series give 1 ÷ (1/10 + 1/22 + 1/47) ≈ 5.998 µF, less than the smallest one. Two equal 100 nF capacitors in series make exactly half, 50 nF.
Charge and energy. A 470 µF capacitor charged to 12 V holds Q = 470 µF × 12 V = 5.64 mC, and stores ½ × 470 µF × 12² ≈ 33.84 mJ.
Time constant. A 100 µF capacitor charging through a 10 kΩ resistor has τ = 10,000 × 0.0001 = 1 second, so it's nearly full after about 5 seconds.
How to use the capacitor calculator
- Choose Parallel or Series.
- Type the values, separated by commas, with their units.
- Add a voltage if you want the charge and energy.
- Add a resistor value, such as 10k or 4.7k, for the time constant.
- Press Calculate.
Reading capacitor values
Parts lists and schematics often write values in short form. 4n7 means 4.7 nF and 2u2 means 2.2 µF, with the letter taking the place of the decimal point; this calculator understands both styles. Ceramic capacitors are often in picofarads or nanofarads, while electrolytic capacitors are usually in microfarads.
Safety
Large capacitors can hold a dangerous charge long after a circuit is switched off. Discharge them safely through a suitable resistor before handling, and always respect the voltage rating printed on the part.
Why put capacitors in parallel or series?
Designers combine capacitors when a single part with the right value isn't available or isn't suitable. Putting capacitors in parallel builds up a larger value, and spreading the current between several parts can also help where a lot of ripple current flows, such as in a power supply. Putting capacitors in series gives a smaller value and lets the string withstand a higher total voltage than one capacitor could on its own, because the voltage is shared between them.
When you connect capacitors in series for voltage, remember that the share each one takes depends on its capacitance. If the values aren't equal, the smallest capacitor takes the largest part of the voltage, so check that no single part goes over its rating. In practice, matched capacitors are used, often with a resistor across each one to balance the voltage.
Typical values
Small ceramic capacitors of a few picofarads to a few hundred nanofarads are used for filtering, timing and decoupling near chips, with 100 nF being a very common value. Electrolytic capacitors from about 1 µF to thousands of microfarads smooth power supplies and store energy. Supercapacitors reach whole farads and more, and they're used to back up memory or deliver short bursts of power.
Common mistakes
- Using the resistor rules. Capacitors add in parallel, not in series.
- Mixing units. 100n is 0.1 µF, not 100 µF.
- Forgetting to square the voltage in the energy formula.
- Ignoring the voltage rating when putting capacitors in series.
What next
Use this often? Add Capacitor to your Home screen.
Frequently asked questions
How does the capacitor calculator work?
It adds capacitances for a parallel connection and adds their reciprocals for a series connection. With a voltage it also gives Q = CV and W = ½CV², and with a resistor the time constant τ = RC.
How do capacitors add in parallel?
They simply add: 10 µF, 22 µF and 47 µF in parallel make 79 µF.
How do you calculate capacitors in series?
Add the reciprocals and take the reciprocal of the sum: 1/C = 1/C₁ + 1/C₂ + …. Two equal capacitors in series give half the value of one.
How much energy does a capacitor store?
W = ½ × C × V². A 470 µF capacitor at 12 V stores about 33.84 mJ.
What is an RC time constant?
τ = R × C. After one time constant a charging capacitor reaches about 63% of the supply voltage, and after about five it's nearly full.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.