Saved

Press the star next to a tool's name to save it.

All my tools

Resistor Series Parallel Calculator

Enter your resistor values, choose series or parallel, and this resistor series parallel calculator finds the total resistance, plus current and power if you add a voltage.

Restored your last values ·

Use k for kilohms and M for megohms. 4.7k and 4k7 both mean 4,700 ohms.

Total resistance

–

Enter your resistor values and press Calculate.

A resistor series parallel calculator finds the single resistance that a group of resistors acts like. In series, you add the values together. In parallel, you add their reciprocals and then take the reciprocal of the sum. Enter as many values as you like in this resistor series parallel calculator, choose how they are connected, and read the total resistance. Add a supply voltage if you want to see the total current, the total power, and the voltage, current and power of each resistor.

Series and parallel formulas

The total resistance of two or more resistors connected in series is equal to the sum of their individual resistances:

R = R1 + R2 + … + Rn

For resistors in parallel, the reciprocals add up:

R = 1 ÷ (1/R1 + 1/R2 + … + 1/Rn)

For exactly two resistors in parallel, this simplifies to a handy shortcut known as product over sum: R = (R1 × R2) ÷ (R1 + R2). The total parallel resistance is always less than the smallest resistor in the group.

How to use the resistor series parallel calculator

  1. Choose Series or Parallel.
  2. Type your resistor values, separated by commas.
  3. Add the voltage across the group, if you want current and power.
  4. Press Calculate to see the results.

You can use common shorthand. Type 470 for 470 ohms, 4.7k or 4k7 for 4,700 ohms, and 2.2M for 2,200,000 ohms.

Worked examples

In series: resistors of 100 Ω, 220 Ω and 330 Ω add up to 100 + 220 + 330 = 650 Ω. On a 12 V supply, the current is 12 ÷ 650, or about 18.46 mA, and the total power is about 221.5 mW.

In parallel: the same three resistors give 1 ÷ (1/100 + 1/220 + 1/330), or about 56.9 Ω, which is less than the smallest resistor. On 12 V, the 100 Ω resistor carries 12 ÷ 100 = 120 mA and dissipates 1.44 W.

Two in parallel: 100 Ω and 220 Ω give (100 × 220) ÷ (100 + 220) = 68.75 Ω.

What is the difference between series and parallel?

SeriesParallel
CurrentThe same through every resistorDivides between the branches
VoltageDivides across the resistorsThe same across every branch
Total resistanceThe sum of the valuesLess than the smallest value

In a series circuit, the current is the same for all of the elements, and the total voltage is the sum of the voltage drops. In a parallel circuit, each component has the same voltage across it, and the total current is the sum of the currents through the branches.

How current and power are worked out

Once the total resistance is known, Ohm's law gives the rest. The law is written V = I × R, where V is the voltage in volts, I is the current in amperes and R is the resistance in ohms. The calculator divides your voltage by the total resistance to find the total current, and it multiplies voltage by current to find the power in watts. In a series circuit, it then finds each resistor's own share of the voltage. In a parallel circuit, it finds the current in each branch.

Why combine resistors?

  • Reaching a value you don't have. Combining standard parts can get close to the value you need.
  • Sharing power. Several resistors can share heat that would be too much for one.
  • Dividing voltage. Two resistors in series form a simple voltage divider.
  • Adding precision. A parallel pair can fine-tune a value.

Check the power rating

Every resistor has a power rating, and exceeding it can make the part overheat. After you enter a voltage, compare each resistor's power with the rating on its data sheet. In the parallel example above, the 100 Ω resistor dissipates 1.44 W, which would be far too much for a part with a much lower rating. It is common practice to choose a part with a comfortable margin above the power you've calculated, especially in a closed enclosure, where heat can't easily escape.

Mixed circuits

Many real circuits combine both arrangements. To solve one, work from the inside out. Replace each parallel group with its equivalent value, then add that value to anything in series with it, and repeat until you have a single figure. Run this calculator once for each step, using the result of one step as an input to the next.

Understanding the results

The table shows how many resistors you've entered, how they are connected and the total resistance. If you add a voltage, you will also see the total current drawn from the supply and the total power that is turned into heat. The second table lists every resistor in the order you typed it, with the voltage across it, the current through it and the power it dissipates. In series, notice that the largest resistor takes the largest share of the voltage. In parallel, it is the smallest resistor that carries the most current, because the voltage across every branch is the same. Units change automatically, so a small current appears in milliamps or microamps and a large resistance appears in kilohms or megohms, which keeps the numbers easy to read at a glance.

Common mistakes

  • Adding parallel values. Parallel resistance goes down, not up.
  • Mixing up units. A kilohm is 1,000 ohms.
  • Ignoring tolerance. Real parts differ a little from their labels.
  • Measuring in a live circuit. Other parts can change the reading.

Estimate run time with the battery life calculator, and check how much electricity your devices use with the appliance power consumption calculator.

What next

Use this often? Add Resistor Ser to your Home screen.

Frequently asked questions

How does the resistor series parallel calculator work?

It adds the values for series, and it adds the reciprocals for parallel, then shows the total resistance.

How do I calculate two resistors in parallel?

Multiply them, then divide by their sum. 100 Ω and 220 Ω give 68.75 Ω.

Is parallel resistance always smaller?

Yes. The total is always less than the smallest resistor in the group.

Can I type values like 4.7k?

Yes. You can use k for kilohms and M for megohms, and shorthand such as 4k7 also works.

Why should I enter a voltage?

With a voltage, the tool can also show the current and power, in total and for each resistor.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools