The resistor color code calculator reads the value of a resistor from the colored bands painted on it, and works the other way too: type a value such as 4.7k and it shows the colors to look for. It handles 3, 4, 5 and 6-band resistors, shows the tolerance and the range the real value can fall in, and draws the resistor so you can compare it with the part in your hand. For example, yellow, violet, red and gold is 4.7 kΩ ±5%.
How to use the resistor color code calculator
- Choose the number of bands on your resistor.
- Hold the resistor with the tolerance band, often gold or silver and set slightly apart, on the right.
- Pick each color from left to right. The drawing updates as you go.
- Read the resistance, tolerance and value range.
- Or switch to Colors from a value and type a resistance to see its bands.
Reading the bands
- 4 bands: two digits, a multiplier and a tolerance. This is the most common type.
- 5 bands: three digits, a multiplier and a tolerance, used for precision resistors.
- 6 bands: like 5 bands, plus a temperature coefficient showing how much the value drifts with heat.
- 3 bands: two digits and a multiplier, with no tolerance band, meaning ±20%.
The color code chart
| Color | Digit | Multiplier | Tolerance |
|---|---|---|---|
| Black | 0 | ×1 | |
| Brown | 1 | ×10 | ±1% |
| Red | 2 | ×100 | ±2% |
| Orange | 3 | ×1,000 | ±0.05% |
| Yellow | 4 | ×10,000 | ±0.02% |
| Green | 5 | ×100,000 | ±0.5% |
| Blue | 6 | ×1,000,000 | ±0.25% |
| Violet | 7 | ×10,000,000 | ±0.1% |
| Gray | 8 | ×100,000,000 | ±0.01% |
| White | 9 | ×1,000,000,000 | |
| Gold | ×0.1 | ±5% | |
| Silver | ×0.01 | ±10% |
These colors follow the international standard IEC 60062. A classic memory aid for the digit order is the phrase “Big Brown Rabbits Often Yield Great Big Vocal Groans When Gingerly Snapped”: black, brown, red, orange, yellow, green, blue, violet, gray, white, then gold and silver.
Worked examples
- Brown, black, red, gold: 1, 0, ×100 = 1,000 Ω = 1 kΩ, ±5%, so 950 Ω to 1,050 Ω.
- Yellow, violet, gold, gold: 4, 7, ×0.1 = 4.7 Ω, ±5%.
- Brown, black, black, brown, brown (5 bands): 1, 0, 0, ×10 = 1,000 Ω, ±1%.
- Red, red, silver, gold: 2, 2, ×0.01 = 0.22 Ω, ±5%.
Which end do I start from?
The first band is usually closest to one end, and the tolerance band is often wider or spaced farther from the others. Gold and silver never appear as the first band, so if one end is gold or silver, start from the other end. If you’re still unsure, try both directions: often only one gives a standard value such as 4.7 kΩ or 10 kΩ. When in doubt, measure with a multimeter.
Standard values and tolerance
Resistors are made in standard series of values. The E12 series, common for ±10% parts, includes 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68 and 82, times powers of ten. The E24 series adds more steps for ±5% parts, and the E96 series is used for ±1% precision resistors. A 5% resistor marked 1 kΩ can measure anywhere from 950 Ω to 1,050 Ω and still be in spec.
Finding colors from a value
Type the resistance using k for thousands and M for millions, such as 470, 2.2k or 1M, and choose the number of bands. With 4 bands, a value needs two significant digits; 4.75 kΩ needs three, so choose 5 bands for it. Use Show to load the colors into the picker.
Surface-mount resistor codes
Tiny surface-mount (SMD) resistors don’t have color bands. Instead they’re printed with a three- or four-digit number, which works like the bands: the first digits are the value and the last digit is the multiplier. So 472 means 47 × 100 = 4,700 Ω, and 1002 means 100 × 100 = 10 kΩ. An R marks the decimal point, so 4R7 is 4.7 Ω. Precision parts may use the EIA-96 code, a two-digit number and a letter, which needs its own table.
Common mistakes
- Reading the resistor backwards. Start from the end opposite the tolerance band.
- Confusing similar colors such as red and orange, brown and red, or blue and violet, especially under warm lighting. Check in daylight or use a magnifier.
- Mistaking a 5-band resistor for a 4-band one. Count the bands before you start.
- Forgetting the tolerance. A ±5% 100 Ω resistor can measure 95 Ω to 105 Ω.
Measuring to be sure
If bands are faded or burned, set a multimeter to resistance (Ω), turn off the circuit, and measure the resistor out of the circuit or with one end lifted, since other parts can change the reading. Compare the result with the nearest standard value.
Temperature coefficient
The sixth band on a 6-band resistor shows how much its value changes as it warms up, in parts per million per kelvin (ppm/K). Brown means 100 ppm/K: a 10 kΩ resistor changes by about 1 Ω for every degree Celsius. Lower numbers, such as red at 50 or orange at 15, matter in precision measuring circuits and audio equipment.
Picking a replacement resistor
When you replace a burned or broken resistor, match three things: the resistance, the tolerance and the power rating. The power rating, such as 1/4 watt or 1/2 watt, isn’t shown by the colors; it’s judged by size, as bigger resistors handle more power. If you can’t find the exact value, the nearest standard value is usually fine in simple circuits, but precision circuits such as filters and sensors need the exact value and tolerance.
To combine resistors, use the series and parallel resistor calculator, and estimate how long a circuit will run with the battery life calculator.
What next
Use this often? Add Resistor Col to your Home screen.
Frequently asked questions
How does the resistor color code calculator work?
It reads the digit bands as a number, multiplies by the multiplier band, and shows the tolerance band as a ± percentage.
What do gold and silver bands mean?
As the last band, gold is ±5% and silver ±10% tolerance. As a multiplier, gold is ×0.1 and silver ×0.01.
What color is a 10k resistor?
Brown, black, orange, then the tolerance band, such as gold for ±5%. That’s 1, 0 and ×1,000.
What color is a 220 ohm resistor?
Red, red, brown, then the tolerance band. That’s 2, 2 and ×10.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.