Saved

Press the star next to a tool's name to save it.

All my tools

Piston Speed Calculator

Use this piston speed calculator to find the mean piston speed of an engine from its stroke and rpm, in feet per minute, metres per second, mph or kilometres per hour.

Restored your last values ·

rpm

Choose US or metric units. Enter the stroke of the engine and its speed in revolutions per minute to get the mean piston speed.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the stroke and the engine speed, then press Calculate.

See full result

This piston speed calculator gives the mean speed of an engine piston from its stroke and the engine speed. Enter the stroke in inches or millimetres and the revolutions per minute, and it returns the speed in feet per minute and metres per second, with miles and kilometres per hour.

How to use the piston speed calculator

  1. Choose US or metric units.
  2. Enter the stroke of the engine.
  3. Enter the engine speed in rpm.
  4. Press Calculate.

What mean piston speed is

Mean piston speed is the average speed of the piston in a reciprocating engine. The piston stops at the top and the bottom of each stroke and moves fastest in between, so its real speed changes all the time. The speed varies through the cycle, so the mean is used as a practical stand-in [1]. Engineers use the mean to compare engines and to check the loads on rods, bolts and the crankshaft.

The formula

Mean piston speed is 2 × stroke × RPM. The Wikipedia article gives the same relation in metric form, as 2 × stroke in millimetres ÷ 1000 × RPM ÷ 60, which gives metres per second [1]. The division by 1000 converts millimetres to metres and the division by 60 converts minutes to seconds. The calculator applies the right conversion for the unit system you pick.

Why the factor of 2

Each turn of the crankshaft moves the piston up and down once, which is two strokes. Wikipedia explains that the factor of 2 is there because one stroke happens in half of a crank revolution [1]. In other words, a full turn involves two strokes. So the piston travels two stroke lengths for each revolution, and the mean speed is that distance times the revolutions per minute.

A US example

Take a stroke of 5 inches at 1,000 rpm. The speed is 2 × 5 × 1,000 = 10,000 inches per minute, which is 833.3 feet per minute. This is our own worked example. Choose US units, enter 5 and 1000, and the calculator shows the same figure, with 4.2333 metres per second as the metric equivalent. The conversion from inches to feet uses the exact value of 12 inches to the foot.

The Wikipedia example

The Wikipedia article takes a piston with a stroke of 90 millimetres at 3,000 rpm: 2 × (90 ÷ 1000) × 3,000 ÷ 60 = 9 metres per second [1]. Choose metric units, type 90 and 3000, and you get 9 metres per second, which is 32.4 kilometres per hour. Our own working converts it to 29.5 feet per second, or 1,771 feet per minute, and 20.1 miles per hour.

A production car

The Wikipedia article says that the 5.2 litre V10 engine of the 2009 Audi R8 has the highest mean piston speed of any production car, at 26.9 metres per second [1]. The article bases the claim on a single manufacturer source, so treat it as the manufacturer's statement. You can try the calculator with a stroke of 92.8 millimetres at 8,700 rpm to see roughly the same figure.

Why it matters

A higher piston speed means more wear and more stress on the engine, which is why engine builders look at it when they choose a stroke or a rev limit. Two engines with the same rpm but different strokes will have different piston speeds. The calculator lets you compare a short stroke with a long one at the same engine speed, and shows how much a higher rev limit raises the figure.

Units

In US mode the stroke is in inches and the main result is in feet per minute, with metres per second, miles per hour and kilometres per hour alongside. In metric mode the stroke is in millimetres and the main result is in metres per second. The calculator uses the exact factors of 0.0254 metres to the inch and 0.3048 metres to the foot, so the two systems agree.

Using the tool

Find the stroke in the engine specification, not the bore, because the stroke is the distance that the piston travels. Enter the speed in revolutions per minute, such as the rev limit if you want the maximum. The result is the mean piston speed at that rpm. Repeat it for the idle speed, the peak power and the rev limit to see how it changes across the range.

Limits

The result is only the mean. The instantaneous speed is higher than the mean in the middle of each stroke, and zero at the ends. The tool does not model the connecting rod length, which changes how the speed varies through the stroke, nor the limits of a given engine. Check the maximum permitted piston speed with the engine builder.

Comparing engines

To compare two engines, enter the stroke and the rev limit of each one. A long stroke engine and a short stroke engine can reach the same mean piston speed at very different rpm, because the speed is proportional to the product of the two. For example, an engine with half the stroke can turn twice as fast for the same mean speed. This is why short stroke engines are used for high revving designs, as the Wikipedia article explains [1].

Checking the numbers by hand

You can check any result by hand. In US units, multiply the stroke in inches by the rpm and by two, then divide by twelve to get feet per minute. In metric units, multiply the stroke in millimetres by the rpm and by two, then divide by sixty thousand to get metres per second [1]. If the answer does not match, check that you used the stroke and not the bore, and that the rpm is the engine speed.

Common mistakes

  • Using the bore instead of the stroke. The stroke is the distance that the piston moves.
  • Forgetting the factor of 2. There are two strokes in every turn.
  • Mixing inches and millimetres. Choose the unit system first.
  • Reading the mean as the maximum. The piston is faster than the mean in mid-stroke.

What next

Use this often? Add Piston Speed to your Home screen.

Frequently asked questions

What is a piston speed calculator?

A tool that gives the mean speed of an engine piston from the stroke and the engine speed.

What is the piston speed formula?

Mean piston speed = 2 × stroke × rpm, with a division by 60 when the result is wanted per second.

Why is there a factor of 2?

The piston makes two strokes, up and down, for each turn of the crankshaft.

What is the mean piston speed of a 90 mm stroke at 3,000 rpm?

9 metres per second, the example given on Wikipedia.

Is the mean the same as the maximum piston speed?

No. The piston moves faster than the mean in the middle of the stroke and stops at both ends.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools