A speedometer gear calculator finds the number of teeth you need on the driven gear of a mechanical speedometer, so that the speedometer reads correctly after you change the tyres or the axle. Enter the tyre diameter, the axle ratio and the teeth on the drive gear, and the calculator gives the revolutions per mile, the gear ratio and the driven gear. It uses the driven-gear formula that Ford Racing publishes,[1] with a divisor of 1,001 in place of its 1,000. It runs in your browser and nothing you enter is sent anywhere.
How to use the speedometer gear calculator
- Choose US or Metric units.
- Enter the tyre diameter and the axle ratio.
- Enter the number of teeth on the drive gear.
- Press Find the gear.
The formulas
The revolutions per mile are 20,168 divided by the tyre diameter in inches. The number 20,168 is another way of writing 63,360 divided by pi: a mile is 5,280 feet, which is 63,360 inches,[3] and one turn of a tyre covers its circumference, which is pi times its diameter.[4] Ford Racing says to take the revolutions per mile from the tyre maker for oversize or undersize tyres, so use the maker's figure if you have it.[1] The driven gear has the drive gear teeth times the axle ratio times the revolutions per mile, divided by a constant. Ford Racing divides by 1,000,[1] while this calculator divides by 1,001, our own choice, which gives a ratio about 0.1 percent lower. The gear ratio is the axle ratio times the revolutions per mile, divided by 1,001, and the driven gear has the gear ratio times the teeth on the drive gear.
Worked example
Our example is a tyre of 20 inches, an axle ratio of 3 and a drive gear of 40 teeth. The revolutions per mile are 20,168 divided by 20, which is 1,008.4. The gear ratio is 3 times 1,008.4 divided by 1,001, which is about 3.02, and the driven gear has 3.02 times 40, or about 120.9 teeth. Because a gear has a whole number of teeth, you round up to 121. With Ford Racing's divisor of 1,000, the same inputs give exactly 121.0 teeth, so both versions point to the same gear. This calculator shows the driven gear.
Why the gears matter
Many speedometers use a rotating flexible cable driven by gearing linked to the transmission, and their calibration depends on the tail shaft gears that drive the cable, the final drive ratio and the tyre diameter.[2] If you fit larger tyres or change the axle ratio, the number of turns per mile changes, and the speedometer reads wrongly. Ford Racing publishes a chart of driven gears that give approximately correct readings for its axle ratios.[1]
Rounding and choices
Gears are made with a whole number of teeth, and a supplier may offer only certain sizes. You may need to use the nearest size that is available, and Ford Racing's own example picks the closest whole number of teeth.[1] Try rounding up and down and see the effect: one tooth in 121 changes the reading by less than one percent. Use the drive gear that is in your transmission, or ask the supplier which drive gears fit.
Limits of the method
The method covers mechanical speedometers only. The divisor assumes a standard cable calibration, which is our assumption, so a speedometer with a different calibration will give wrong answers. Electronic speedometers do not use gears, and need a different kind of correction, such as the one in our pulse per mile calculator. Check the result with a GPS reading at a steady speed.
Reading the result
The calculator shows the revolutions per mile of your tyre, the gear ratio that the speedometer needs, the number of teeth on the driven gear and the same number rounded up to a whole number of teeth. The number to order is the rounded one. If the exact value is close to a whole number, the rounded gear will be very accurate, and if it is halfway between two whole numbers, consider the effect of rounding up and down on the reading.
Checking the reading after the change
After you fit the new gear, test the speedometer. Drive at a steady speed on a clear road and compare the reading with a GPS device, or time yourself over a measured distance between mile markers. If the reading is off by more than a few percent, check the tyre diameter and the axle ratio you used, and measure the tyre again with the vehicle loaded, since the diameter under load is a little smaller than the diameter when the tyre is off the ground.
Tyres and axle ratios together
The calculator can handle a change of both. Enter the new tyre diameter and the new axle ratio together, and it gives the gear for the combination. If you only change the tyres, enter the new diameter and your existing axle ratio. The result is the gear that makes the speedometer read the true speed for that setup.
Common mistakes
- Mixing up the drive and driven gears. The result is the driven gear.
- Using the rim size. Enter the overall tyre diameter.
- Forgetting the axle ratio. The final drive changes the shaft speed.
- Using it for an electronic speedometer. It has no gears to change.
What next
Use this often? Add Speedometer to your Home screen.
Frequently asked questions
What is a speedometer gear calculator?
A tool that finds the speedometer driven gear that matches your tyre size and axle ratio.
How do you calculate revolutions per mile?
20,168 divided by the tyre diameter in inches, which is 63,360 ÷ π ÷ diameter.
What is the gear ratio formula?
Gear ratio = axle ratio × revolutions per mile ÷ 1,001, and the driven gear = ratio × drive gear teeth. Ford Racing divides by 1,000.
What is the answer for a 20 inch tyre, a 3.0 axle and a 40 tooth drive gear?
About 120.9 teeth, which rounds up to 121 teeth.
Does it work for electronic speedometers?
No. It is for mechanical ones, and it assumes a standard cable calibration.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.