A nusselt number calculator compares convective heat transfer with conduction. It works from the definition Nu = h L ÷ k, from correlations for natural and forced convection, and, as a related step, it finds the Prandtl number from a fluid's viscosity, heat capacity and conductivity.
How to use the nusselt number calculator
- Choose the mode: definition, natural convection, forced convection or Prandtl number.
- Fill in the boxes that appear for that mode, using the units shown beside each.
- Optionally add L and k to a correlation to see the heat transfer coefficient h.
- Press Calculate.
What the Nusselt number is
The Nusselt number is the ratio of the heat transferred by convection to the heat transferred by conduction, Nu = q_conv ÷ q_cond. In working form Wikipedia defines it as Nu = h L ÷ k, a nondimensional convective heat transfer coefficient [1]. The numbers h_c in W/m²·K, L in metres and k_f in W/m·K make it dimensionless, so a Nusselt number of 20 means convection moves about 20 times as much heat as conduction through the same layer.
The definition mode
Enter the convective heat transfer coefficient, the characteristic length of the surface in the direction of heat transfer and the thermal conductivity of the fluid. For h = 25 W/m²·K, L = 0.5 m and k = 0.6 W/m·K the result is 20.83. Find the fluid's thermal conductivity first if you do not know it; the calculator does not look up fluid properties.
Natural convection
For natural convection the calculator uses Nu = C Ra^n, with coefficients that depend on the shape and the flow. These are textbook values that we could not tie to a freely readable primary page, so check them against your own reference; Wikipedia gives other correlations, such as the Churchill–Chu form [1]. For a vertical plate the laminar case is C = 0.59 and n = 1/4 for Ra from 10⁴ to 10⁹, and the turbulent case is C = 0.1 and n = 1/3 up to 10¹³. For a horizontal isothermal cylinder it is 0.48 and 1/4 up to 10⁷, then 0.125 and 1/3 up to 10¹². A Rayleigh number of 10⁶ on a plate gives 18.66.
Forced convection over a plate
For forced convection the calculator uses Nu = C Re^m Pr^n. For a flat plate, Wikipedia gives the laminar isothermal average as Nu = 0.664 Re^(1/2) Pr^(1/3) for Pr above 0.6 [1], which the calculator writes with n = 0.33. The turbulent plate case, for Re from 5 × 10⁵ to 10⁷ with Pr from 0.6 to 60, uses C = 0.037, m = 0.8 and n = 0.33, a textbook correlation that Wikipedia's page does not list. The 5 × 10⁵ boundary between laminar and turbulent flow is the calculator's own choice.
Forced convection in a pipe
For a pipe, Wikipedia gives fixed values for fully developed laminar flow: Nu = 3.66 at constant surface temperature and 4.36 at constant heat flux. For turbulent flow with Re above 10⁴ and Pr from 0.6 to 160 it gives the Dittus–Boelter form Nu = 0.023 Re^0.8 Pr^n, with n = 0.4 for heating and 0.3 for cooling [1]. The calculator offers all four cases, and returns an error outside the stated ranges instead of extrapolating.
A worked check
For gas heated in a pipe with Re = 10⁴ and Pr = 1, the turbulent formula gives 0.023 × 10^(4 × 0.8) × 1 = 36.45, and the calculator returns that value. Natural convection can give a Nusselt number above 10 at high Rayleigh numbers, as the coefficients above show.
The Prandtl number
The Prandtl number is the ratio of momentum diffusivity to thermal diffusivity, Pr = ν ÷ α = c_p μ ÷ k [2]. As an example, water with a viscosity of 1.002 mPa·s, a heat capacity of 4184 J/kg·K and a conductivity of 0.607 W/m·K, gives about 6.9. This calculator returns 6.907, and with the optional density 997 kg/m³ it also gives ν and α.
What Prandtl values mean
Wikipedia's table lists typical values: liquid metals far below 1, from 0.00013 for lead at 1000 K to 0.003 for potassium, gases around 0.7, such as 0.70 to 0.73 for air, and liquid water from 10.6 at 280 K to 2.0 at 360 K [2]. A low Prandtl number means heat spreads faster than momentum, and a high one means momentum spreads faster. The calculator labels your result in those terms.
Prandtl number calculator
This page also does the job of a separate Prandtl number calculator: choose the Prandtl mode and enter the viscosity in mPa·s, the specific heat and the thermal conductivity. The number you get can be carried straight into the forced convection mode, together with a Reynolds number, to find the Nusselt number and, with L and k, the heat transfer coefficient h = Nu k ÷ L, which is our own rearrangement of the definition.
Limits and when to use it
These are empirical correlations for simple shapes and steady flow, accurate to a modest percentage at best. They do not cover rough surfaces, mixed convection, developing flow near a pipe inlet or liquid metals. Use the calculator to learn how Nu, Re, Pr and Ra fit together, to check a textbook problem or to make a first estimate, and verify any design with the correlation recommended for your geometry.
Reading the result
The first line gives the Nusselt number, the second says which correlation was used, and the third translates it into how many times convection beats conduction. If you supplied L and k, the last line gives the heat transfer coefficient. A higher Nusselt number means a thinner boundary layer and more effective heat transfer, so compare cases to see how flow speed or surface shape changes it.
Common mistakes
- Using the wrong length. L is the characteristic length in the heat transfer direction, not just any size.
- Using a correlation outside its range. The tool refuses a Reynolds, Prandtl or Rayleigh number outside the stated limits.
- Mixing heating and cooling. The turbulent pipe exponent is 0.4 for heating and 0.3 for cooling.
- Entering viscosity in Pa·s. The Prandtl mode wants millipascal seconds.
What next
Use this often? Add Nusselt Numb to your Home screen.
Frequently asked questions
What is a nusselt number calculator?
A tool that finds the Nusselt number, the ratio of convective to conductive heat transfer, from h, L and k or from convection correlations.
What is the Nusselt number formula?
Nu = h L ÷ k, where h is the convective heat transfer coefficient, L the characteristic length and k the fluid's thermal conductivity.
What is the Prandtl number formula?
Pr = c_p μ ÷ k, which equals the kinematic viscosity divided by the thermal diffusivity.
Which correlation is used for turbulent pipe flow?
Nu = 0.023 Re^0.8 Pr^n with n = 0.4 for heating and 0.3 for cooling, for Re above 10⁴.
Is there a separate Prandtl number calculator?
Not here. Choose the Prandtl number mode on this page.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.