An MLVSS calculator works out the mixed liquor volatile suspended solids of an activated sludge tank. It has two uses: the mass and concentration of MLVSS a tank needs for a chosen food-to-microorganism ratio, and the MLVSS of a lab sample from its dried and burnt weights. It follows the food-to-microorganism ratio as defined in operator training material [1].
How to use the MLVSS calculator
- Choose what you know: the flow and COD, the COD load, or a lab sample.
- Pick US or metric units (not needed for the lab test).
- Fill in the boxes and press Calculate.
What MLVSS means
MLVSS is the organic, or volatile, part of the suspended solids in the mixed liquor of an aeration tank, and it is used as a measure of the microorganisms present [1]. Pennsylvania's operator training module says it should be between 70 and 80 percent of the MLSS [1]. Treating all of the volatile solids as bacteria is a simplification, but it gives a workable number for a design. Standard Methods lists method 2540E for fixed and volatile solids ignited at 550 degrees Celsius [2].
The plant formulas
In plant mode, the flow in gallons per hour becomes million gallons per day by multiplying by 24 and dividing by 1,000,000. The COD reaching the aeration tank is the influent COD minus the COD removed in primary treatment. The F/M ratio is the mass of food per unit mass of MLVSS per day, in pounds of BOD or COD per pound of MLVSS per day [1]. The COD load in pounds per day is the flow in million gallons per day times that COD in milligrams per litre times 8.34, the conversion factor between milligrams per litre and pounds per million gallons [1]. The MLVSS mass is the load divided by the F/M ratio, which follows from the definition of F/M.
A worked plant example
Take 125,000 gallons per hour, an influent COD of 500 and a primary treatment figure of 300 milligrams per litre, with an F/M ratio of 0.4. The flow is 3 million gallons per day, the COD to the tank is 200, and the load is 3 times 200 times 8.34, which is 5,004 pounds per day. The MLVSS mass is 5,004 divided by 0.4, or 12,510 pounds. This is our own example, built on the formulas above.
Entering the load directly
If you already know the COD load, the second mode skips the flow and the COD and takes the load directly. A COD load of 3,000 pounds per day and an F/M ratio of 0.65 give 3,000 divided by 0.65, which is 4,615.4 pounds of MLVSS. This is our own example.
The F/M ratio
F/M stands for food to microorganisms. The Pennsylvania module gives typical values in pounds of COD per pound of MLVSS per day: above 1.0 for high-rate plants, 0.5 to 1.0 for conventional plants and below 0.2 for extended aeration [1]. The tool also compares your figure with a general band of 0.3 to 0.6, which is a guide of our own and not a figure from that module. An F/M of 0.65 is just above our band, and the tool says so, though it lies inside the conventional range above.
The concentration
If you enter the tank volume, the tool also gives the MLVSS concentration. The factor 8.34 converts milligrams per litre into pounds per million gallons [1]. So one milligram per litre is 8.34 times 10 to the minus 6 pounds per gallon, and with the volume in gallons the concentration is the mass divided by the volume times 8.34 times 10 to the minus 6. That step is our own arithmetic. For the example, the 12,510 pounds in 1,500,000 gallons give 1,000 milligrams per litre.
The metric version
The training module works in US units. Our metric version, which is our own working, drops the 8.34 factor: the flow in cubic metres per hour times 24 times the COD in milligrams per litre, divided by 1,000, gives kilograms of COD per day. The MLVSS mass in kilograms divided by the volume in cubic metres, times 1,000, gives milligrams per litre. With 500 cubic metres per hour, the same 200 milligrams per litre and an F/M of 0.4, the load is 2,400 kilograms and the MLVSS 6,000 kilograms.
The lab test
Standard Methods describes total suspended solids dried at 103 to 105 degrees Celsius (method 2540D) and fixed and volatile solids ignited at 550 degrees Celsius (method 2540E) [2]. In lab mode, the MLSS concentration is the weight of the dried sample divided by its volume. The fixed solids are the weight of the ash divided by the same volume, and the MLVSS is the MLSS minus the fixed solids. The page we read does not give these equations, so they are our own working from the two methods. Weights are in grams and the volume in millilitres, so we multiply by 1,000,000 to give milligrams per litre.
A worked lab example
A filter weighs 1.0000 grams and, with the dried sample, 1.1250 grams. The crucible weighs 20.0000 grams, and with the ash, 20.0400 grams. The sample volume is 50 millilitres. The MLSS is 0.125 divided by 0.05 litres, which is 2,500 milligrams per litre. The fixed solids are 800, so the MLVSS is 1,700 milligrams per litre, and 68 percent of the solids are volatile.
What it leaves out
The tool does not give the solids retention time, the sludge volume index or the wasting rate, which need other formulas that the Pennsylvania module covers [1]. Use the result for a first estimate, and rely on your engineer and your lab method for a design or a permit.
Common mistakes
- Mixing gallons per hour with million gallons per day. Enter the hourly flow, and the tool converts it.
- Using the wrong sample volume. Use millilitres, and the same volume for the MLSS and the ash.
- Treating the COD removed as the COD left. The tool subtracts it from the influent.
- Entering weights in milligrams. Use grams for the lab test.
What next
Use this often? Add MLVSS to your Home screen.
Frequently asked questions
What is an MLVSS calculator?
A tool that works out the volatile suspended solids in an aeration tank, from plant data or a lab test.
How is MLVSS calculated from the F/M ratio?
The MLVSS mass is the COD load divided by the F/M ratio.
What is a normal F/M ratio?
For COD per pound of MLVSS per day, a Pennsylvania training module gives 0.5 to 1.0 for conventional plants and below 0.2 for extended aeration.
How do I find MLVSS in the lab?
Subtract the fixed solids from the MLSS, both found from dried and burnt sample weights.
Does it work in metric units?
Yes. Our metric version drops the 8.34 factor and uses kilograms and cubic metres.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.