A water tank capacity calculator tells you how much a tank holds from its inside measurements. For a rectangular tank, multiply length × width × height. For a round tank, multiply the area of the circle by its length or height. This water tank capacity calculator handles rectangular tanks, upright round tanks and round tanks lying on their side. Enter your measurements to see the capacity in gallons or liters. Add the current water depth to find out how much is in the tank now, and add a fill rate to see how long it will take to fill.
Water tank capacity formulas
- Rectangular: volume = length × width × height
- Vertical round: volume = π × radius² × height
- Horizontal round: volume = π × radius² × length
To turn cubic feet into US gallons, remember that the US gallon is legally defined as exactly 231 cubic inches, and a cubic foot contains 1,728 cubic inches. So gallons = cubic feet × 1,728 ÷ 231. A US gallon is 3.785411784 liters. In metric, 1 cubic meter holds 1,000 liters.
How to use the water tank capacity calculator
- Choose your units. US is selected first.
- Choose the shape of your tank.
- Measure the inside of the tank, and enter the sizes.
- Add the water depth, if you want to know how much is in it now.
- Add a fill rate, if you want an estimated filling time.
- Press Calculate.
Worked examples
Rectangular: a tank 6 ft long, 4 ft wide and 3 ft high holds 6 × 4 × 3 = 72 cubic feet. That's 72 × 1,728 ÷ 231 = about 538.6 gallons. If the water is 1.5 ft deep, the tank is half full, with about 269.3 gallons in it. At 10 gallons per minute, filling the rest takes about 27 minutes.
Vertical round: a tank 4 ft across and 6 ft high holds π × 2² × 6, which is about 75.4 cubic feet, or 564 gallons.
Horizontal round: a tank 4 ft across and 8 ft long holds about 752 gallons.
Metric: a tank 2 m × 1.5 m × 1 m holds 3 cubic meters, or 3,000 liters.
Why horizontal tanks are different
In a rectangular or upright tank, the amount of water rises in a straight line with the depth, so half the depth is half the water. A round tank lying on its side doesn't behave that way, because it's narrow at the bottom, widest in the middle and narrow again at the top. At a depth that's a quarter of the diameter, the tank is far less than a quarter full. The calculator uses the area of a circular segment to get this right: area = R² × arccos(1 − h ÷ R) − (R − h) × √(h × (2R − h)), where R is the radius and h is the depth of the water. It then multiplies that area by the tank's length.
How heavy is a full tank?
Water is heavier than many people expect. The density of water is about 1 gram per cubic centimeter, so a liter weighs about a kilogram. A US gallon holds about 8.3454 lb of water at its densest. The 538.6-gallon tank in the first example would weigh about 4,495 lb when full, before you count the weight of the tank itself. That's why it's so important to check that a floor, roof or stand can carry the load. If you are in any doubt, ask a structural engineer before you install a large tank.
Measuring accurately
- Measure inside the tank. Walls can be surprisingly thick.
- Measure the diameter at the widest point, straight across the center.
- Measure depth with a clean rod or a tape, and hold it vertically.
- Allow for the fittings. Pipes, floats and baffles take up some space.
- Don't count the top few inches if an overflow pipe stops the water below that point.
Actual capacity and usable capacity
The figure here is the geometric volume of the shape. In practice, you can rarely use all of it. An outlet usually sits a little above the floor of a tank, so some water stays below it, and an overflow keeps the water from reaching the very top. To estimate the usable amount, measure the depth between the outlet and the overflow, and enter that as your height. For a storage tank that's meant for an emergency, this usable figure is the one that matters.
Choosing the right size of tank
Start by working out how much water you use in a typical day, and then decide how many days of storage you would like to have. Multiply the two, and add a margin for dry spells or for an interruption in your supply. Try different dimensions in the calculator until you find a shape that holds that amount and also fits your space. Remember to leave room around the tank for access and maintenance, and think about how water will get in and out of it.
Common mistakes
- Using the outside measurements. You'll overestimate the capacity.
- Confusing diameter and radius. Enter the full distance across.
- Mixing up gallon types. This tool uses US gallons.
Related tools
Work out other shapes with the volume and surface area calculator, plan a slab with the concrete calculator, and measure rooms with the square footage calculator.
What next
Use this often? Add Water Tank C to your Home screen.
Frequently asked questions
How does a water tank capacity calculator work?
It works out the volume of your tank's shape, then converts that volume into gallons or liters.
How many gallons are in a cubic foot?
A cubic foot is 1,728 cubic inches, and a US gallon is 231 cubic inches, so it's about 7.48 gallons.
Can it handle a tank lying on its side?
Yes. Choose Horizontal round, and it allows for the curved shape when you enter a water depth.
How much does the water weigh?
A liter of water weighs about a kilogram. The results show the weight of a full tank.
Should I measure the inside or the outside?
Measure the inside, since the walls don't hold any water.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.