A concentration calculator converts between the units that chemists use for how much of a substance is dissolved in a solution. Enter the concentration in one unit, with the molar mass of the solute and the density of the solution, and you get it back as molarity, mass concentration, percent by mass, percent weight in volume, parts per million, molality, mole fraction and normality. It covers the usual jobs of turning mass concentration into molar concentration and a percentage into molarity.
How to use the concentration calculator
- Choose the unit that you know and enter its value.
- Enter the molar mass of the solute and the density of the solution.
- Add the equivalents per mole if you need normality, or the solvent's molar mass if it is not water.
- Press Convert.
Molarity and mass concentration
Molarity is the number of moles of solute per litre of solution [1]. Multiplying it by the molar mass gives the mass concentration in grams per litre [1], and dividing a mass concentration by the molar mass gives the molarity back. A solution of 116 grams per litre of sodium chloride, which has a molar mass of 58 grams per mole, is 2 moles per litre. The mass of solute in a given volume works the same way: 11.6 grams in 0.1 litres is 116 grams per litre.
Percent by mass and density
Percent by mass is 100 times the mass fraction, the mass of the solute over the mass of the whole solution [6]. The mass fraction equals the molarity times the molar mass, divided by the density of the solution [1]. The page gives a worked example: 11.6 grams of sodium chloride in 100 grams of water is 10.4 percent by mass, the solution has a density of 1.07 and its molarity is 1.92 mol/L [1]. Entering 10.4 percent, a molar mass of 58 and a density of 1.07 gives 1.9186 mol/L, which agrees. The mass fraction does not change with temperature, which is one of its advantages [6].
Molality
Molality is the amount of solute divided by the mass of the solvent, in moles per kilogram [2]. It does not change with temperature, but it depends on which component you call the solvent [2]. The molality follows from the molarity by b = c divided by (ρ − cM), with the density in kilograms per litre and the molar mass in kilograms per mole [1]. For the example above, it is 2.0012 mol/kg, which matches 0.2 moles in 100 grams of water. NIST regards the unit symbol m and the word molal as obsolete [2].
Mole fraction
The mole fraction of a component is its amount divided by the total amount of all the components in the mixture, and the mole fractions add up to 1 [3]. The calculator takes the solvent to be water, with a molar mass of 18.015 grams per mole, unless you enter another molar mass, and divides the moles of solute by the moles of solute and solvent. For the example, the mole fraction of the salt is 0.0348. A mole percent is 100 times the mole fraction [3].
Normality
Normality is the number of equivalents of solute per litre of solution, and it equals the molarity times the equivalents per mole [4]. A 1 M solution of sulfuric acid is 2 N, because each mole gives two hydrogen ions, and a 1 M solution of phosphoric acid is 3 N in a reaction that uses all three [4]. IUPAC and NIST discourage the term normality [4]. Enter the number of equivalents for your reaction in the box, or leave it at 1.
Parts per million
The notation ppm means a fraction of 10⁻⁶ [5]. It is ambiguous, because it may refer to mass, moles or volume, so write out the units where it matters [5]. For a dilute water solution of density 1.00 g/mL, 1 ppm is about 1 milligram per litre [5]. The calculator shows both the milligrams per litre and the parts per million by mass, and for the example the solution is 104,000 ppm by mass.
Percent weight in volume
A percent weight in volume is the number of grams of solute in 100 millilitres of solution, so 1 percent w/v is 10 grams per litre. The page on mass fractions does not define this unit, so this is our own working. It is common for laboratory stock solutions and medicines.
Worked example
Take a 0.5 mol/L solution of glucose, molar mass 180 grams per mole, with a density of 1.02 grams per millilitre. The mass concentration is 90 grams per litre, the percent weight in volume is 9, and the percent by mass is 8.82. The molality is about 0.55 mol/kg. These are our own calculations from the formulas above.
Choosing a unit
The unit you choose depends on the job. Molarity suits reactions in solution because it counts molecules, and it is the unit of most laboratory stock solutions. Mass concentration and percentages suit recipes and products, where you weigh the solute. Molality and mole fraction suit studies in which temperature changes, since they do not depend on volume. Parts per million suit traces, such as minerals in water.
Common mistakes
- Using the wrong density. The default of 1 g/mL suits only dilute solutions.
- Mixing molarity and molality. One is per litre of solution and the other per kilogram of solvent.
- Forgetting equivalents. Normality needs the equivalents per mole.
- Treating ppm as a mass when it is a volume. Say which one you mean.
What next
Use this often? Add Concentratio to your Home screen.
Frequently asked questions
What is a concentration calculator?
A tool that converts a concentration from one unit to others, such as molarity, grams per litre, percent by mass, ppm, molality, mole fraction and normality.
How do I convert mass concentration to molarity?
Divide the grams per litre by the molar mass in grams per mole. 116 g/L of a substance of 58 g/mol is 2 mol/L.
How do I convert percent to molarity?
Multiply the percent by mass by the density in g/mL and by 10, then divide by the molar mass. 10.4 percent, density 1.07 and 58 g/mol give 1.92 mol/L.
What is the difference between molarity and molality?
Molarity is moles per litre of solution, and molality is moles per kilogram of solvent. Molality does not change with temperature.
How many mg/L is 1 ppm?
About 1 mg/L for a dilute water solution with a density of 1.00 g/mL.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.