An LC filter calculator finds the cutoff frequency of a low-pass or high-pass filter built from one inductor and one capacitor. It also works backwards: enter the cutoff you want and one part, and it gives the other part. The same formula gives the resonant frequency of an LC circuit, so it also covers the resonant frequency LC calculator job.
How to use the LC filter calculator
- Choose what to find: the cutoff frequency, the inductance or the capacitance.
- Enter the other two values: inductance in millihenries, capacitance in nanofarads and frequency in hertz.
- Press Calculate and read the result and the notes.
The cutoff frequency formula
The cutoff frequency of an LC filter is f = 1 ÷ (2π √(L C)), with L in henries and C in farads [1]. The calculator takes the inductance in millihenries and the capacitance in nanofarads, and converts them before it uses the formula. The result is shown in hertz and in kilohertz so that you can compare it quickly with an audio or radio band.
Resonant frequency of an LC circuit
The same expression is the resonant frequency of an LC circuit. The angular frequency is ω₀ = 1 ÷ √(L C), and the frequency in hertz is f₀ = ω₀ ÷ 2π [1]. Because the two formulas match, one tool serves for a filter cutoff and for a resonant frequency. Searches for a resonant frequency LC calculator land on this page for that reason.
Solving for L or C
If you know the frequency you want and one of the parts, rearrange the formula. The inductance is L = 1 ÷ ((2π f)² C) and the capacitance is C = 1 ÷ ((2π f)² L). These rearrangements are our own algebra. They follow directly from squaring both sides of the cutoff formula [1].
A worked example
For a 1 kHz cutoff with a 47 nF capacitor, the formula gives an inductance of about 0.5389 henries, or 538.9 millihenries. Choose the inductance in the calculator, type 1000 for the frequency and 47 for the capacitance, and you get 538.94 mH. Put that value back in the cutoff mode and the frequency returns as 1,000 Hz, which is a useful check.
Low-pass and high-pass layouts
In a low-pass filter the inductor sits in series with the load and the capacitor sits across it [3]. In a high-pass filter the positions are swapped: the capacitor is in series and the inductor is across the load, which is our own description of the dual arrangement. The corner frequency is the same formula for both. Only the arrangement of the parts decides which frequencies pass and which are blocked, so the result line repeats this reminder.
What happens at the cutoff
At the cutoff frequency the filter attenuates the input power by half, which is 3 dB, and a real filter changes gradually rather than at one sharp step [2]. An LC filter is a second-order filter, so its roll-off is about twice as steep as that of a first-order RC or RL stage: 40 dB per decade against 20 dB per decade for a Butterworth response [2]. This is why designers choose LC parts when they need a stronger rejection of unwanted frequencies.
Series and parallel resonance
In a series LC circuit the two reactances cancel at the resonant frequency, the current is at its maximum and the impedance approaches zero [1]. In a parallel circuit the line current is at its minimum at resonance [1]. These facts explain why the same formula can describe a band-pass or a band-stop network, depending on how the circuit is connected.
Characteristic impedance
The calculator also shows √(L ÷ C) in ohms. This is our own working, not a figure from either source. It is the impedance that an LC filter is commonly matched to, so it helps you to judge whether the load you plan to connect is sensible. For the 10 mH and 100 nF example it is 316.23 ohms.
Component limits
The formula assumes ideal parts. Real inductors have winding resistance and real capacitors have tolerances of several percent, so the true corner can differ from the calculated one. The source and load impedances also move the corner. Treat the result as a starting design, build the filter, and measure it with a signal generator.
Choosing the parts
Start from the cutoff you want and pick a standard capacitor value that is easy to buy, such as 47 nF or 100 nF. Then use the inductance mode to find the coil. If the coil comes out too large or too small to wind or buy, pick another capacitor and try again. A larger capacitor gives a smaller inductor for the same frequency, which is often cheaper and lighter.
Checking your answer
Enter the result back in the cutoff mode. The frequency should return to the value you started with. For the example in this article, 538.94 mH and 47 nF give 1,000 Hz. Also compare the characteristic impedance with the load. A load much lower or higher than that value makes the real filter peak or droop near the corner, so adjust the design or add a damping resistor.
Common mistakes
- Entering the capacitance in microfarads. The box expects nanofarads, so 0.047 µF is 47 nF.
- Entering the inductance in henries. The box expects millihenries, so 0.5 H is 500 mH.
- Forgetting the 2π. The cutoff is in hertz, not in radians per second.
- Expecting a sharp edge. The gain falls gradually after the −3 dB corner.
What next
Use this often? Add LC Filter to your Home screen.
Frequently asked questions
What is an LC filter calculator?
A tool that finds the cutoff frequency of an inductor and capacitor filter, or the L or C needed for a target frequency.
What is the LC cutoff formula?
f = 1 ÷ (2π √(L C)), with L in henries and C in farads.
Is the cutoff frequency the same as the resonant frequency?
Yes, for the ideal LC circuit both use the same expression, f = 1 ÷ (2π √(L C)).
Is an LC filter better than an RC filter?
It is second order, so it rolls off twice as steeply, but it needs an inductor and is more sensitive to the source and load.
Which values does the calculator expect?
Inductance in millihenries, capacitance in nanofarads and frequency in hertz.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.