This ev charger circuit calculator helps you plan the circuit for a home or workplace electric vehicle charger. A charger that pushes 48 amps for hours is a continuous load, and electrical codes treat continuous loads with extra margin. Enter the charger's rated amps to see the minimum circuit rating and the next standard breaker size.
How to use the ev charger circuit calculator
- Find the rated output current on the charger label or in its manual. For a plug-in unit, use the current it is set to deliver.
- Type the amps in the first box.
- Optionally type the supply voltage. The default is 240 V, common for Level 2 charging in North America.
- Press Calculate to see the minimum circuit amps, the charging power and the next standard breaker size.
The 125 percent rule
The U.S. Department of Energy guide for EV charging states that charging is a continuous load, and that the NEC requires wiring size and overcurrent protection for chargers to be 125 percent of the charger's nameplate continuous output rating [1] Wikipedia describes the same idea in the history of the code: protection at 125 percent of the maximum rated current, so a Level 2 setup needing 40 amps of supply is protected at 50 amps [2] The calculator multiplies your charger amps by 1.25.
Worked example
A charger is rated 48 amps. 48 × 1.25 = 60 amps, so the circuit needs to be rated at least 60 amps. At 240 volts the charging power is 48 × 240 = 11,520 watts, or 11.52 kW. The next standard breaker size is 60 amps, so a 60 amp breaker fits exactly.
Common charger ratings and breakers
| Charger rating | Minimum circuit (×1.25) | Next standard breaker |
|---|---|---|
| 16 A | 20 A | 20 A |
| 24 A | 30 A | 30 A |
| 32 A | 40 A | 40 A |
| 40 A | 50 A | 50 A |
| 48 A | 60 A | 60 A |
| 30 A | 37.5 A | 40 A |
The "next standard breaker" column uses a common list of standard sizes. That list is our own working, not a quote from a code table, so check it against the code edition that applies to you.
Why the extra 25 percent
Breakers and wiring run warm when they carry a full load for a long time. A charger can draw its full current for several hours. The margin keeps the breaker and conductors from running at their limit for that whole time, which cuts the chance of nuisance trips and overheating.
What this calculator does not do
- It does not pick the wire size. Wire ampacity depends on the conductor material, insulation, terminal temperature rating and installation conditions, so use the tables in the code edition in force or ask an electrician.
- It does not check whether your panel has spare capacity. A load calculation of the whole home may be needed.
- It does not cover load sharing or energy management systems, which can allow a smaller circuit.
- It does not cover the receptacle. Not every plug is rated for a full continuous load.
Charging power and time
Charging power is amps times volts. At 240 volts, a 32 amp charger delivers 7.68 kW and a 48 amp charger delivers 11.52 kW. Divide a battery size in kWh by the power to get a rough charge time, for example a 60 kWh battery from empty at 11.52 kW takes about 5.2 hours. That is our own working and ignores charging losses and the car's own charge limit, so real times are longer.
Breaker size versus wire size
Choosing the breaker is only half the job. The wire must carry at least the circuit rating after the installation conditions are applied, and the breaker protects that wire. A bigger breaker on the same wire removes the protection. If you raise the charger current later, the circuit may need to be redone. Ask the electrician which amperage the installed wire supports so you know how much room you have to upgrade.
Plug-in chargers and receptacles
Some chargers plug into a 240 volt receptacle instead of being hard-wired. The receptacle and plug must also suit the continuous current, and a unit may need to be set lower than its maximum for that reason. If you use a plug-in unit, follow the charger maker's instructions on the largest current setting for the receptacle in use, and have the receptacle installed by a qualified electrician.
Common mistakes
- Sizing the breaker at exactly the charger amps. A 48 amp charger on a 50 amp breaker is below the 125 percent rule.
- Using the car's onboard charge rate instead of the charger's rating.
- Assuming a breaker bigger than needed is always fine. The wire must be rated for the breaker.
- Forgetting that a charger set to a lower current may be allowed a smaller circuit if the unit supports that. Follow the maker's instructions.
Before you install
This tool gives an estimate only. A licensed electrician should size the wire, check the panel and pull any permit. Many places require a permit and an inspection for a new EV charger circuit. The DOE guide also lists ground-fault protection and the use of a dedicated branch circuit for EV equipment as part of the NEC requirements [1] Ask your local building department which code edition applies to you.
What next
Use this often? Add EV Charger C to your Home screen.
Frequently asked questions
How does the ev charger circuit calculator work?
It multiplies the charger rated amps by 1.25 to get the minimum circuit rating, then shows the next standard breaker size from a common list.
What size breaker do I need for a 48 amp EV charger?
48 amps times 1.25 is 60 amps, so a 60 amp breaker is the minimum. A smaller breaker would fall below the 125 percent rule.
Why is an EV charger a continuous load?
A charger can draw its full current for hours. Electrical codes treat loads that run for three hours or more as continuous, so the circuit is sized with extra margin.
Does this calculator choose the wire size?
No. Wire size depends on the code edition, conductor type, terminal rating and installation. Ask a licensed electrician to size the wire.
Can I use a 50 amp breaker for a 40 amp charger?
Yes. 40 amps times 1.25 is 50 amps, so a 50 amp circuit matches a 40 amp charger. Confirm with your electrician and the local code.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.