This countersink depth calculator works out how deep to cut a countersink so a flat-head screw sits flush with the surface. Choose the countersink angle, enter the diameter you need at the surface and, if there's one, the pilot hole diameter, and the countersink depth calculator gives the depth of the cone below the surface and the depth from the cutter's point.
How to use the countersink depth calculator
- Choose inches or millimeters.
- Choose the countersink angle: 82° for inch screws, 90° for metric screws, 100° for aerospace fasteners, or another angle.
- Enter the countersink diameter at the surface, usually the screw head's diameter.
- Enter the pilot hole diameter if the screw passes through a drilled hole, then press Calculate.
Countersink angles
According to Wikipedia, countersink cutters come in six common angles: 60°, 82°, 90°, 100°, 110° and 120°. The two most common are 82° and 90°. Unified (inch) countersunk screws very often have an 82° head, ISO metric screws very often have 90°, and in aerospace countersunk fasteners typically have 100°. Matching the countersink angle to the screw head lets the head bear evenly on the cone and sit flush.
The countersink formula
A countersink is a cone. If the included angle is α, each side is at α ÷ 2 from the axis, and the cone's radius grows by tan(α ÷ 2) for every unit of depth. So the depth from the cone's point to reach a diameter D at the surface is:
depth from point = (D ÷ 2) ÷ tan(α ÷ 2)
When there's a pilot hole of diameter d, the cone starts where it meets the hole, so the countersink itself is only:
countersink depth = (D − d) ÷ 2 ÷ tan(α ÷ 2)
Worked example
Take a 1/4-inch pilot hole that needs an 82° countersink 0.5 inches across at the surface. The half angle is 41°, and tan 41° ≈ 0.869. The countersink depth is (0.5 − 0.25) ÷ 2 ÷ 0.869 = 0.144 inches below the surface. Measured from the cutter's point, the depth is 0.25 ÷ 0.869 = 0.288 inches, which is what you'd set on a depth stop if you zero the cutter's tip at the surface.
In metric, a 90° countersink 12 mm across over a 6.6 mm hole is (12 − 6.6) ÷ 2 ÷ tan 45° = 2.7 mm deep, and 6 mm from the point.
Reading the results
The big number is the depth of the countersink below the surface, where the cone meets the pilot hole. The table shows the depth from the cutter's point, the included angle and the half angle on each side.
Setting the depth on a drill press
On a drill press or mill, the simplest method is to touch the countersink cutter's point to the surface, zero the depth stop, and plunge by the depth from the point. Because cutters' tips are often slightly rounded or truncated, check the first hole by trying the screw, and adjust before you do the rest. For a screw that should sit slightly below the surface, add that amount to the depth.
Why the angle matters
Using the wrong angle leaves the screw head touching the cone only at its top or bottom edge. An 82° screw in a 90° countersink bears only at the outer rim, and a 90° screw in an 82° countersink bears near the shank. Either way, the head may not sit flush and the joint is weaker. Check whether your screws are inch or metric before choosing.
Finding the head diameter
The countersink diameter at the surface should match the largest diameter of the screw head, so the head sits flush. Measure it with calipers or take it from the screw maker's data. If you want the head slightly below the surface, for example so it can be filled over, use a slightly larger diameter, which makes the countersink a little deeper.
Changing the angle
For the same surface diameter, a smaller included angle makes a deeper countersink and a larger angle a shallower one. For a 0.5-inch countersink measured from the point, a 60° cone is about 0.433 inches deep, an 82° cone about 0.288 inches, a 90° cone 0.25 inches and a 120° cone about 0.144 inches. That's why the angle must match the screw: the head and the cone only fit together when they're the same.
Thin materials
In thin sheet, a countersink can be deeper than the material is thick, leaving a knife edge or no material for the head to bear on. Check that the countersink depth is less than the thickness of the part. If it isn't, consider a smaller screw head, a dimpled joint or a different fastener.
Inches or millimeters
Choose the unit that matches your drawing and enter both diameters in it. The calculator shows three decimal places for inches and two for millimeters, enough for most shop work, and the angles stay the same in either unit.
Common mistakes
- Using 90° for inch screws. Most inch flat-heads are 82°.
- Forgetting the pilot hole. The countersink depth is less than the depth from the point.
- Measuring the head wrongly. Use the head's largest diameter.
- Cutting too deep. Test on scrap first.
Tips
- Use a slow speed to reduce chatter.
- Check flushness with the actual screw.
- Use a depth stop for repeat holes.
What next
Use this often? Add Countersink to your Home screen.
Frequently asked questions
How does a countersink depth calculator work?
It treats the countersink as a cone: depth = (D − d) ÷ 2 ÷ tan(angle ÷ 2).
What angle countersink for inch screws?
Usually 82°, according to Wikipedia; ISO metric screws usually use 90°.
How deep should a countersink be?
Deep enough that the cone reaches the screw head's diameter at the surface, so the head sits flush.
How deep is an 82° countersink for a 1/2-inch head?
Over a 1/4-inch hole, about 0.144 inches below the surface.
What countersink angle do aircraft fasteners use?
Typically 100°.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.