Saved

Press the star next to a tool's name to save it.

All my tools

Carburetor CFM Calculator

Use this carburetor CFM calculator to estimate the airflow in cubic feet per minute from the engine displacement, the maximum rpm and the volumetric efficiency.

Restored your last values ·

rpm
%

Enter the engine displacement and choose its unit, the highest rpm you expect and the volumetric efficiency as a percentage. You get the carburetor airflow in cubic feet per minute.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the displacement, the maximum rpm and the efficiency, then press Calculate.

See full result

A carburetor CFM calculator estimates the airflow, in cubic feet per minute, that a carburetor must supply for an engine. Enter the displacement, the maximum rpm and the volumetric efficiency. It gives the size in CFM, with the working shown.

How to use the carburetor CFM calculator

  1. Enter the engine displacement and choose cubic inches, litres or cubic centimetres.
  2. Enter the maximum rpm.
  3. Enter the volumetric efficiency as a percentage.
  4. Press Calculate.

The CFM formula

The OnAllCylinders article from Holley gives the sizing formula as planned rpm times cubic inches divided by 3,456, and says that it assumes 100% volumetric efficiency, so you multiply by about 0.85 for a street car [1]. The calculator uses the same formula, with your efficiency as a decimal: CFM = displacement in cubic inches × maximum rpm × efficiency ÷ 3,456. The result is the airflow that the engine can draw at its top speed, which is the figure that carburetors are rated by.

Where 3,456 comes from

The article does not explain the constant, so this is our own working: a cubic foot holds 1,728 cubic inches, and a four-stroke engine draws its displacement of air once every two turns, so the divisor is 2 × 1,728 = 3,456.

A worked example

Our own example is a 340 cubic inch engine that turns 5,600 rpm with 80% efficiency. Then 340 × 5,600 = 1,904,000, times 0.80 is 1,523,200, and dividing by 3,456 gives 440.74 CFM. The tool shows the same figure.

Volumetric efficiency

The efficiency says how well the engine fills its cylinders with air. The article treats 100% as its base case and applies about 85% for a street car [1]. The calculator also labels your figure with rough bands that are our own rule of thumb, not a standard: about 80% for a stock engine, about 85% for a rebuilt street engine, and 95% to 110% for a race engine. It tells you in which of these regions your value falls. A high figure means that the engine breathes better, and so it needs a larger carburetor.

Units for the displacement

The formula works in cubic inches. The conversion is our own working. An inch is exactly 2.54 centimetres, so a cubic inch is exactly 16.387064 cubic centimetres. The tool divides cubic centimetres by this number, and multiplies litres by 61.0237, which is 1,000 divided by 16.387064.

Checking the numbers

The tool shows the displacement in cubic inches, litres and cubic centimetres, and the product before the division. For 340 cubic inches, that is 5.572 litres or 5,571.6 cc. Comparing the intermediate product with a hand calculation is the quickest way to catch a typing mistake in the rpm or the efficiency.

Why the maximum rpm

The airflow rises with engine speed, so the formula uses the highest rpm that the engine will reach, not the idle speed. If you rarely go above 5,000 rpm, use that figure. A carburetor chosen for a very high rpm can be too large for everyday driving, so think about how the engine is really used before you enter the number.

An estimate, not a tune

The article notes that its formula does not take vehicle weight or rear axle gear ratio into account [1], so we call the result an estimate and not a substitute for tuning. Other makers can recommend different sizes, and many builders choose a slightly larger or smaller carburetor for the way the car is driven. We did not open the pages of other carburetor makers, so the tool does not claim to match them.

Common engine sizes

To see how the size scales, try a few engines. A 350 cubic inch engine at 5,500 rpm and 80% needs about 446 CFM, and a 5.7 litre engine, which is about 348 cubic inches, comes out close to that. The results grow in direct proportion to the displacement, the rpm and the efficiency, so doubling any one of them doubles the airflow.

Using the calculator

Enter your displacement and pick its unit, then the top rpm and an honest efficiency figure. Read the CFM and the working. Try 80% and 85% to see the effect of a rebuilt engine, and then compare the airflow with the CFM rating on the carburetors you are considering, treating the answer as a guide only.

How the inputs act

The airflow is in direct proportion to the displacement, the rpm and the efficiency. If your efficiency figure is five points higher, 85% instead of 80%, the airflow for the example engine rises from 440.74 to about 468.3 CFM, our own arithmetic from the formula. A different engine gives a different answer: a 302 cubic inch engine at 6,000 rpm and 85% comes to about 445.7 CFM. Trying a few values shows how sensitive the result is to your assumptions.

Comparing with carburetor ratings

Carburetors are also sold by CFM, so the result is easy to compare with a catalogue. The article that we used does not say how a carburetor is rated, and we did not open any maker's page, so treat the comparison as rough. Many builders pick the nearest size and then tune, which is a good reason to treat the figure as an estimate. If two carburetors are close to your figure, the choice also depends on how the car is used, so write down the efficiency and the rpm you assumed, and change them one at a time to see which carburetor still fits.

Common mistakes

  • Using the wrong displacement unit. Choose cubic inches, litres or cc to match the figure.
  • Entering the efficiency as a decimal. Type 80, not 0.8.
  • Using the idle rpm. Use the maximum engine speed.
  • Taking it as exact. It is a ballpark estimate.

What next

Use this often? Add Carburetor C to your Home screen.

Frequently asked questions

What is a carburetor CFM calculator?

A tool that estimates the airflow, in cubic feet per minute, an engine needs from its displacement, maximum rpm and volumetric efficiency.

What is the carburetor CFM formula?

CFM = displacement in cubic inches × maximum rpm × efficiency (as a decimal) ÷ 3,456.

What efficiency should I use?

About 80% for a stock engine, about 85% for a rebuilt street engine and 95% to 110% for a race engine are the tool's own rough bands. The OnAllCylinders article uses 100% as its base and about 85% for a street car.

How many CFM does a 340 cubic inch engine need?

At 5,600 rpm and 80% efficiency, about 440.74 CFM.

Is the result exact?

No. It is a ballpark estimate and not a substitute for tuning.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools