This bowl segment calculator works out how to cut the segments for a segmented bowl or vase on the lathe. Enter the outer diameter of a ring, the ring width and the number of segments, and the bowl segment calculator gives the miter angle for each end, the length of the segments' outer and inner edges, and the length of board you need for the ring.
How to use the bowl segment calculator
- Choose inches or millimeters.
- Enter the ring's outer diameter, the largest size the turned ring needs to be.
- Enter the ring width, the width of the board you'll cut the segments from.
- Enter the number of segments in the ring, then press Calculate.
How a segmented ring works
A segmented bowl is built from rings, each glued up from short pieces of wood with angled ends. Joined end to end, the pieces form a regular polygon, such as a hexagon, octagon or dodecagon. The ring is then turned round on the lathe. For the ring to turn to the full outer diameter, the polygon's flat sides must sit outside that circle, so the circle fits inside the polygon.
The formulas
The Wikipedia article on regular polygons gives the side length of a regular polygon with n sides and apothem r (the distance from the center to the middle of a side) as s = 2r × tan(π ÷ n). Its exterior angle is 360° ÷ n, so each joint closes that angle, with half of it cut on each segment end. For a ring with outer diameter D and ring width w:
- Miter angle = 180° ÷ n on each end
- Outer edge length = D × tan(180° ÷ n)
- Inner edge length = (D − 2w) × tan(180° ÷ n)
- Board length = n × outer edge length, before kerf
Worked example
Take a ring with a 10-inch outer diameter, made from a board 1½ inches wide, with 12 segments. The miter angle is 180 ÷ 12 = 15° on each end. Each segment's outer edge is 10 × tan 15° = 2.679 inches, and its inner edge is 7 × tan 15° = 1.876 inches. The 12 segments need about 32.2 inches of board, plus saw kerf and spare. The cut makes a 75° angle with the edge of the board.
An 8-segment ring with an 8-inch outer diameter from a 1-inch board needs 22.5° miters, with outer edges of 3.314 inches and inner edges of 2.485 inches.
Reading the results
The big number is the miter angle for each end of each segment, the angle you set on most miter saws and sleds. The table shows the outer and inner edge lengths, the board length for the whole ring, the angle between the cut and the board edge, and the inside diameter of the ring.
Planning a whole bowl
A segmented bowl stacks several rings of different diameters to follow the bowl's profile. Draw the profile full size, mark each ring's height, and measure the outer diameter each ring needs at its widest point, plus a little extra for turning. Run the calculator for each ring. Many turners keep the same number of segments in every ring and offset each ring by half a segment, like brickwork, so the joints don't line up.
Choosing the number of segments
More segments make each piece shorter and the ring closer to a circle, so less wood is turned away. Fewer segments mean longer pieces and fewer glue joints, but more waste at the corners. For the same 10-inch ring, 8 segments need 22.5° miters and outer edges of about 4.14 inches, 12 segments need 15° miters and 2.68-inch edges, and 16 segments need 11.25° miters and edges of about 1.99 inches. Many patterns use the same count for every ring so the joints can be staggered.
Why small errors matter
A ring has two cut ends at every joint, so any error in the miter angle is doubled at each joint and repeated around the ring. With 12 segments there are 24 cut ends: an error of just 0.1° on each one leaves a 2.4° gap or overlap when the ring closes. That's why turners test the angle on scrap and adjust before cutting good wood.
Inches or millimeters
Choose the unit you measure in. Enter the outer diameter and ring width in the same unit, and the segment lengths and board length come out in that unit. The angles are the same either way, since they depend only on the number of segments.
Write the angle and lengths for each ring on your drawing so you can set up the saw once per ring.
Common mistakes
- Using the finished size. Add a little to the outer diameter for turning.
- Forgetting the kerf. Each cut removes wood, so add it to the board length.
- Small angle errors. A tenth of a degree on each end adds up over many joints.
- Too narrow a board. The ring width sets the bowl's wall thickness.
Tips
- Cut a test ring from scrap to check the angle.
- Use a stop block so every segment is the same length.
- Glue the ring in two halves, flatten the joints, then join the halves.
What next
Use this often? Add Bowl Segment to your Home screen.
Frequently asked questions
How does a bowl segment calculator work?
It treats each ring as a regular polygon: the miter is 180° ÷ n and the outer edge is the diameter × tan(180° ÷ n).
What angle do I cut for 12 segments?
15° on each end of each segment.
What angle do I cut for 8 segments?
22.5° on each end.
How long should each segment be?
Outer edge = outer diameter × tan(180° ÷ number of segments); for a 10-inch, 12-segment ring, about 2.68 inches.
How much board do I need for a ring?
The number of segments times the outer edge length, plus saw kerf and spare.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.