The wainscoting calculator works out the materials to panel the lower part of a room’s walls. Enter the total length of wall to cover, the width of doors and other openings to leave out, and the height of the wainscot, and it works out the area, how many 4 × 8 ft panels (such as beadboard sheets) or how many boards to buy, and the length of chair rail and baseboard. Enter the ceiling height too and it suggests a wainscot height. For example, a 12 × 14 ft dining room with one door has 49 ft of wall; at 32 inches high that’s about 131 sq ft, or 5 sheets of 4 × 8 paneling with 10% extra.
How high should wainscoting be?
Fine Homebuilding’s guide to laying out wainscot paneling says wainscot covers the wall to the height of a chair rail, typically 30 to 42 inches above the floor, and that the author likes to place the chair rail one-third to two-fifths of the way up the wall. On an 8 ft wall that’s 32 to 38.4 inches; on a 9 ft wall, 36 to 43.2 inches. Taller paneling, up to shoulder height or the tops of the doors, is more decorative and suits living rooms, libraries and bedrooms.
How the wainscoting calculator works
- Length to cover = total wall length − doors and other full-height openings.
- Area = length × wainscot height.
- Panels: a 4 × 8 ft sheet stood upright is cut across into strips the height of the wainscot, so each sheet gives as many strips as fit in 96 inches, each 4 ft wide. At 32 inches that’s 3 strips, or 12 ft of wall per sheet.
- Boards: the number of boards across the wall = length ÷ board width; each 8 ft board gives as many pieces as fit in 96 inches.
- Trim: the chair rail (or cap) and the baseboard each run the full length.
How to use the wainscoting calculator
- Choose panels or boards, and US or metric units.
- Enter the total wall length: add up every wall in the room you are covering.
- Enter the width of doors and other openings that run to the floor.
- Enter the wainscot height, and the ceiling height if you want a suggestion.
- For boards, enter the board’s face width.
- Set the waste allowance (10% if blank) and the price per sheet or board.
Worked example
A dining room 12 × 14 ft has 52 ft of wall. Leaving out a 3 ft doorway gives 49 ft. At 32 inches high:
- Area: 49 × 32 ÷ 12 = 130.7 sq ft
- Length with 10% waste: 53.9 ft
- Each 4 × 8 sheet gives 3 strips 32 inches high, covering 12 ft of wall
- Sheets: 53.9 ÷ 12 = 4.5, so 5 sheets
- Chair rail and baseboard: 53.9 ft each
For an 8 ft ceiling the calculator suggests 32 to 38.4 inches, so 32 inches sits at the low end of the range.
Planning around windows
Windows usually sit above the chair rail, so the wainscot runs under them and the calculator doesn’t subtract them. If a window or a counter comes down below the wainscot height, subtract its width as an opening and plan to fit the paneling around it. Fine Homebuilding notes that it’s simplest when door and window casings stand proud of the paneling, chair rail and baseboard, so the paneling can butt against the trim.
Styles of wainscoting
- Beadboard: panels or tongue-and-groove boards with narrow vertical grooves, common in kitchens, bathrooms and cottages.
- Raised or flat panel: frames of rails and stiles around panels, a more formal look for dining rooms and halls.
- Board and batten: flat panels with vertical battens, popular in modern farmhouse rooms.
For frame-and-panel styles, Fine Homebuilding suggests rails and stiles between 2 and 3½ inches wide and keeping the stiles the same width as the rails.
Finishing
Paint or prime panels before installing if you can, especially the edges and grooves. Caulk the joints between the paneling and the trim, and fill nail holes before the final coat. Work out the paint with the paint calculator.
Measuring the room
Measure each wall at the height of the wainscot rather than at the floor, as baseboard heaters, built-ins or stair stringers can change the run. Add the walls together for the total length, then add the width of each door and any other opening that runs from floor to ceiling. Inside and outside corners need a little extra trim for the miters, which the waste allowance covers.
Board and plank wainscoting
For tongue-and-groove beadboard or other boards fitted side by side, choose Boards and enter the width of one board’s visible face. The calculator works out how many boards fit across the wall and how many pieces of the wainscot height you can cut from each 8 ft board. If you buy longer boards, divide the pieces by the number that fit in your length instead.
Metric units
In metric mode, enter the wall length in meters and the heights in centimeters. Panel sizes stay at 4 × 8 ft (about 1.22 × 2.44 m), and the trim lengths show in meters.
For full-height boards, try the shiplap calculator, and for an odd-shaped room the square footage calculator.
What next
Use this often? Add Wainscoting to your Home screen.
Frequently asked questions
How does the wainscoting calculator work out panels?
It finds how many strips of the wainscot height fit in an 8 ft sheet, multiplies by 4 ft for the wall each sheet covers, and divides your wall length (plus waste) by that.
How high should wainscoting be?
Typically 30 to 42 inches. Fine Homebuilding suggests one-third to two-fifths of the wall height: 32 to 38 inches on an 8 ft wall.
How many 4 × 8 panels do I need for a 12 × 14 room?
With one 3 ft door and 32 inch wainscot, about 5 sheets with 10% extra.
Do I subtract windows when measuring for wainscoting?
Usually not, as windows sit above the chair rail. Subtract doors and anything that runs to the floor.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.