Saved

Press the star next to a tool's name to save it.

All my tools

Shiplap Calculator

Enter the wall’s width and height and choose your shiplap board. The shiplap calculator uses the board’s exposed face to work out the linear feet, the number of boards, the rows up the wall and the cost.

Restored your last values ·

The visible width of one board after the overlap.

Linear feet = area × 12 ÷ exposed face, plus waste. Blank waste uses 10%.

Boards to buy

–

Enter the wall’s width and height.

See full result

The shiplap calculator works out how much shiplap you need for an accent wall, a whole room or a ceiling. Enter the width and height of the wall, subtract any windows and doors, and choose the board width. Because shiplap boards overlap, each one covers less than its full width, so the calculator uses the board’s exposed face to work out the linear feet, the number of boards of the length you buy, the number of rows up the wall and the cost. For example, a 12 × 8 ft wall in 1×6 shiplap needs about 247 linear feet with 10% waste, or 31 boards 8 ft long.

The shiplap formula

US Lumber’s coverage table gives a simple method for wood siding and paneling: multiply the square footage to be covered by the lineal foot factor, which is 12 inches divided by the board’s exposed face width. So:

  • Linear feet = area (sq ft) × 12 ÷ exposed face (inches), plus waste
  • Boards = linear feet ÷ board length, rounded up
  • Rows = wall height (inches) ÷ exposed face, rounded up

Exposed face widths

For shiplap-style patterns (drop, tongue-and-groove and channel rustic), US Lumber lists these exposed faces:

Nominal widthExposed faceLinear feet per sq ft
1×43⅛ in3.84
1×65⅛ in2.34
1×86⅞ in1.75
1×108⅞ in1.35

Boards from different mills and the MDF or plywood shiplap planks sold in home centers can have a different exposure, so measure one or check the product label. Choose “Custom” to enter your own exposed width.

How to use the shiplap calculator

  1. Choose US or metric units.
  2. Enter the wall width and height. For a ceiling, enter its length and width.
  3. Enter the area of windows and doors to leave out.
  4. Choose the board width and the length you’ll buy.
  5. Set the waste allowance (10% if blank) and the price per linear foot.

Worked examples

Accent wall: a wall 12 ft wide and 8 ft high is 96 sq ft. With 1×6 shiplap the factor is 12 ÷ 5.125 = 2.34, so 96 × 2.34 = 224.8 linear feet, or 247.3 with 10% waste. That’s 31 boards 8 ft long, laid in 19 rows.

Wall with a window: the same wall with 20 sq ft of window needs 76 × 2.34 × 1.1 = 195.7 linear feet, or 17 boards 12 ft long.

Why add waste?

Every row needs cuts at the ends, and cuts around windows, outlets and corners create short offcuts that can’t always be used elsewhere. Boards can also have knots or splits you’ll want to avoid on a feature wall. 10% is a reasonable starting point for a plain wall; raise it for walls with lots of openings or if you want to stagger the joints in a set pattern.

Choosing board length

Longer boards mean fewer joints, which looks cleaner on a feature wall. If a board can span the whole wall, you avoid joints altogether. On longer walls, stagger the joints from row to row and place them over studs so each end can be nailed. The calculator’s board count assumes offcuts are reused where possible; with very long boards on a short wall, you may need a few extra.

Installation tips

  • Find the studs and mark them on the floor and ceiling so you can nail into them.
  • Start at the bottom and check the first row is level; every row above follows it.
  • Use spacers, such as a coin or a nickel, to keep an even gap if your boards don’t lock together.
  • Paint or stain first if you want the gaps finished, as it’s hard to reach them afterward.

Shiplap on a ceiling

For a ceiling, enter the room’s length and width instead of the wall’s width and height. The linear feet and boards are worked out the same way. On a ceiling, run the boards across the joists so every board can be nailed into several joists, and plan the first row along the most visible wall so any narrow cut row ends up where it’s least noticed.

Real shiplap vs. paneling

Traditional shiplap is solid wood with a rabbeted edge, so each board overlaps the next. Many products sold as shiplap today are MDF or plywood planks with a nickel gap, or tongue-and-groove boards with a shiplap look. They are often sold by the plank, covering a stated square footage per piece, or in packs. If yours is sold that way, divide the area to cover (plus waste) by the coverage of one piece instead.

Metric units

In metric mode, enter the wall size in meters. The board widths stay in inches, as they are sold that way, and the result shows linear meters as well as the number of boards.

Before you start

Let solid wood boards sit in the room for a few days before you install them, so they adjust to the indoor humidity and don’t shrink or swell after they’re nailed up. Remove outlet covers and trim, and plan how the boards will meet at corners and around windows before you make the first cut.

Work out paint for the finished wall with the paint calculator, the lumber volume with the board foot calculator, and the area of an odd-shaped room with the square footage calculator.

What next

Use this often? Add Shiplap to your Home screen.

Frequently asked questions

How does the shiplap calculator work out linear feet?

It multiplies the area by 12 divided by the board’s exposed face width, then adds your waste allowance.

How much shiplap do I need for a 12 × 8 ft wall?

With 1×6 shiplap (5⅛ inch exposure), about 225 linear feet, or 247 with 10% waste: 31 boards 8 ft long.

How wide is the exposed face of 1×6 shiplap?

US Lumber lists 5⅛ inches for 1×6 drop, tongue-and-groove and channel rustic patterns. Check your product, as it can vary.

How many rows of shiplap for an 8 ft wall?

With a 5⅛ inch exposure, 96 ÷ 5.125 = 18.7, so 19 rows.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools