Saved

Press the star next to a tool's name to save it.

All my tools

Vickers Hardness Number Calculator

Use this Vickers hardness number calculator to find HV from the test force and the diagonal of the indentation, with the hardness in MPa and GPa and a rough tensile strength.

Restored your last values ·

Enter the test force in newtons or kilograms-force and the diagonal of the square indentation in millimetres. For a better average, enter both diagonals. You get the Vickers hardness number, the hardness in MPa and GPa and a rough tensile strength.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the test force and the diagonal of the indentation, then press Calculate.

See full result

A Vickers hardness number calculator turns the force of a diamond pyramid indenter and the size of the mark that it leaves into a hardness number, HV. Enter the test force and the diagonal of the square indentation, and read the hardness in kgf/mm², in megapascals and a rough tensile strength.

How to use the Vickers hardness number calculator

  1. Enter the test force and pick newtons or kgf.
  2. Enter the diagonal of the indentation in millimetres, or both diagonals.
  3. Press Calculate.

The Vickers test

In the Vickers test a diamond pyramid is pressed into a polished surface with a known force, and the diagonals of the square mark are measured under a microscope. The hardness is the force divided by the surface area of the mark. A small mark means a hard material. The test works for thin sections and for hard and soft metals alike, because the shape of the indenter is the same at every load.

The formula

The full formula is HV = 2 F sin(α ÷ 2) ÷ d², with the angle α = 136 degrees, the force F in kilograms-force and the mean diagonal d in millimetres. Wikipedia gives the approximation HV ≈ 1.8544 F ÷ d², with F in kilograms-force and d in millimetres [1]. They agree, because 2 sin 68 degrees is 1.8544. The calculator uses the sine form.

The 136 degree angle

The pyramid has an angle of 136 degrees between opposite faces. Wikipedia says that this angle was chosen as the included angle between the plane faces of the tip [1]. We do not repeat the reasoning, which the page gives in a form that we could read only in summary. What matters is that the same angle gives the same hardness number at different loads, which is why a single constant converts diagonal to hardness.

Newtons and kilograms-force

The formula needs the force in kilograms-force. If you enter newtons, the calculator divides by 9.80665 first. With the force in newtons the coefficient becomes about 0.1891, as Wikipedia gives [1], which is 1.8544 ÷ 9.80665. For example, 50 newtons and a diagonal of 0.5 millimetres give 37.82 only when the newtons are converted, as the calculator does.

A worked example

For 50 N and a diagonal of 0.5 mm, the force is 5.0986 kgf, and HV = 1.8544 × 5.0986 ÷ 0.25 = 37.82 kgf/mm². As a pressure, 37.82 × 9.80665 gives 370.9 MPa, or 0.3709 GPa. The tensile strength estimate is 370.9 ÷ 3 = 123.6 MPa, as explained below.

Hardness in pressure units

To turn the hardness into a pressure, multiply by 9.80665 for megapascals and divide by 1,000 for gigapascals. Wikipedia gives the same conversion in the form GPa = (9.80665 ÷ 1000) × HV [1]. The calculator shows both megapascals and gigapascals. A hardness of 100 HV is about 981 megapascals, which is why the numbers in the Vickers scale are close to the strength of a metal in tens of megapascals.

The tensile strength rule

Wikipedia gives an empirical rule that the tensile strength in megapascals is about the hardness in megapascals divided by a constant of about 3, with the constant usually between 2 and 4 and depending on how the material work-hardens [1]. The calculator uses 3, so 370.9 MPa gives 123.6 MPa. Treat the figure as a rough guide for a metal, and not for ceramics, polymers or a thin coating.

Reporting the result

Wikipedia shows that a Vickers result is reported with the load, for instance 440HV30, where 30 is the force in kilograms-force, and lists 316L stainless steel as 140HV30 [1]. The calculator writes the result in the same form, for example 330.9 HV30 for 30 kgf. The load matters, because a small load tests a thin layer and a large load a deeper volume.

Two diagonals

The two diagonals of the mark should be almost equal. If they are not, the surface or the alignment may be at fault. The calculator uses the mean of the two, d = (d₁ + d₂) ÷ 2. For 0.4 mm and 0.42 mm at 30 kgf, d is 0.41 mm and the hardness is 330.9 HV. If you enter only the first diagonal, the calculator takes both as equal.

Limits

The calculator does the arithmetic for a test that has been carried out correctly. A real test needs a flat, polished surface, the right load for the thickness, and a calibrated machine, as set by the test standard. The marks should also be well away from edges and from one another. The result does not replace a certified test report.

Reading the three numbers

The first line is the standard Vickers number in kilograms-force per square millimetre, the figure that appears on drawings and test reports. The second line gives the same hardness as a pressure, which is handy when you compare it with a yield or tensile strength in megapascals. The third line is only a rough estimate for metals. If you test several marks on one sample, run each one through the calculator and average the hardness numbers, rather than averaging the diagonals, and report the load with the result so that others can repeat the test.

Common mistakes

  • Entering the diagonal in micrometres. Use millimetres.
  • Entering newtons but choosing kgf. The result would be ten times too large.
  • Using the hardness as the tensile strength. Divide by about 3 for a metal.
  • Dropping the load from the report. Write HV with the load, such as HV30.

What next

Use this often? Add Vickers Hard to your Home screen.

Frequently asked questions

What is a Vickers hardness number calculator?

A tool that finds HV from the test force and the diagonal of the indentation.

What is the Vickers hardness formula?

HV = 2 F sin(136° ÷ 2) ÷ d², about 1.8544 F ÷ d² with F in kgf and d in mm.

How do I convert HV to MPa?

Multiply by 9.80665.

How is the tensile strength estimated?

With the rule of thumb strength = hardness ÷ 3 for metals.

What does HV30 mean?

A Vickers hardness measured with a force of 30 kgf.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools