Saved

Press the star next to a tool's name to save it.

All my tools

True Strain Calculator

Use this true strain calculator to convert lengths or engineering strain to true strain, ln(1 + e), and engineering stress to true stress for a sample in uniform tension.

Restored your last values ·

%

Enter the original and final lengths of a sample, or its engineering strain in percent. You get the true (logarithmic) strain. Add the engineering stress to get the true stress too.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what you have and fill in the boxes, then press Calculate.

See full result

A true strain calculator converts the lengths of a stretched sample, or its engineering strain, into the true strain, which is the natural logarithm of the length ratio. Add the engineering stress to find the true stress as well. It is the standard way to turn engineering stress-strain data into true stress-strain data.

How to use the true strain calculator

  1. Choose lengths or engineering strain.
  2. Enter the original length and the final length, or the strain in percent.
  3. Add the engineering stress if you want the true stress.
  4. Press Calculate.

Engineering and true strain

Engineering strain is the change in length divided by the original length. It uses the starting length for the whole test. True strain uses the instantaneous length. The page defines true strain as ε_T = ln(l_i ÷ l₀), where l_i is the instantaneous measured length of the sample [1]. For small strains the two are almost equal, but they drift apart as a sample stretches.

The conversion

With engineering strain e = (l − l₀) ÷ l₀, the final length is l = l₀ (1 + e). Putting that into the definition gives ε = ln(1 + e). This step is our own working from the definition on the page [1]. For an engineering strain of 20 percent, the true strain is ln 1.2 = 0.1823, or 18.23 percent. The true strain is always smaller than the engineering strain in tension.

True stress

The page defines true stress as σ_T = F ÷ A_i, where F is the instantaneous load applied perpendicular to the cross section and A_i is the instantaneous cross-sectional area [1]. The engineering stress uses the original area instead. If the volume stays constant, then A_i = A₀ l₀ ÷ l, and the true stress becomes σ_T = σ_eng (1 + e), a standard relation that is our own working, since the page does not write it.

A worked example

A sample 100 millimetres long is stretched to 120 millimetres, so e = 0.2. The true strain is 0.182322. If the engineering stress is 200 megapascals, the true stress is 200 × 1.2 = 240 megapascals. The calculator accepts any stress unit and returns the answer in the same unit. The numbers are our own example, not taken from the page.

Why true strain is useful

True strain is additive. Stretch a bar from 100 to 120 millimetres and then to 144, and the two logarithmic strains, 0.1823 each, add to 0.3646, which equals ln 1.44. The engineering strains of 20 percent twice do not add to the 44 percent total. This is the reason why large-deformation work, such as forming and rolling, uses true strain.

Compression

The same formula works for a shortened sample. If a 100 millimetre sample is compressed to 80 millimetres, the strain is ln 0.8 = −0.2231. The sign is negative, showing a contraction. The engineering strain would be −20 percent, which is not equal in size to the true strain. The calculator accepts any final length above zero and does not limit you to stretching.

Where it holds

The page notes that the cross-sectional area decreases uniformly along the gauge length, because of the incompressibility of plastic flow, in the uniform part of the test [1]. That is the region where the constant-volume conversion is good. After necking begins, the strain is no longer uniform along the sample, and the conversion from engineering values does not hold, so you need to measure the neck.

Stress keeps growing

The page also makes the point that in the necking region the true stress keeps growing, but the engineering stress decreases, because the engineering stress does not take the shrinking section area into account [1]. This is the reason why engineers convert to true values when they want a material law for a simulation. The calculator gives the converted stress for the uniform part of the test only.

Strain in a rolling or forming job

Metal forming is where true strain is used most. When a bar is rolled or drawn through a die, each pass reduces the length ratio by a certain factor, and the true strains of the passes add up to the total strain. A bar drawn from 100 to 150 millimetres and then to 180 has strains of 0.4055 and 0.1823, which sum to 0.5878, the same as ln 1.8. The calculator gives each step, so you can check the total of a multi-pass schedule against a single calculation.

Units

Lengths can be in any unit, as long as both are the same, since only their ratio matters. The engineering strain is typed in percent. The stress can be in any unit, such as megapascals or pounds per square inch, and the true stress comes out in the same unit. The true strain has no unit. It is shown as a decimal and as a percentage.

Using the calculator

Pick the option you have, then enter the values. Read the true strain, and the true stress if you gave a stress. Check the figures against your test data, and do not apply the stress conversion beyond the point of maximum load. For plasticity models and finite element work, the true stress-strain curve is the standard input, and this tool gives you its points.

Common mistakes

  • Using the stress conversion after necking. It holds only in the uniform region.
  • Mixing the length units. Use one unit for both lengths.
  • Entering strain as a decimal. The box takes percent.
  • Using ln of the strain rather than of the length ratio. Use ln(1 + e).

What next

Use this often? Add True Strain to your Home screen.

Frequently asked questions

What is a true strain calculator?

A tool that converts lengths or engineering strain into the logarithmic strain ln(l ÷ l₀).

What is the formula for true strain?

ε = ln(l ÷ l₀) = ln(1 + e).

How is true stress found from engineering stress?

σ_true = σ_eng (1 + e) while the volume is constant.

Is true strain bigger than engineering strain?

No, in tension the true strain is smaller.

When does the conversion stop working?

Once necking starts and the strain is no longer uniform.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools