Saved

Press the star next to a tool's name to save it.

All my tools

Tree Leaves Calculator

Use this tree leaves calculator to estimate the number of leaves on a tree from a sample count on a plate, the crown diameter and the leaf area index.

Restored your last values ·

Hold a plate or a hoop under a branch and count the leaves that just cover it. Enter its diameter and the count, the width of the crown, and optionally a leaf area index. You get an order-of-magnitude estimate of the leaves on the whole tree.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the plate size, the leaf count and the crown width, then press Calculate.

See full result

A tree leaves calculator estimates how many leaves a tree carries. You count the leaves that cover a plate, measure the width of the crown, and the tool scales the count up to the whole crown with a leaf area index. The answer is a rough order of magnitude, not a count.

How to use the tree leaves calculator

  1. Choose US or metric units.
  2. Enter the diameter of the plate and the leaves that cover it.
  3. Enter the crown diameter.
  4. Leave the leaf area index blank for 4.7, or type your own, and press Calculate.

The idea behind it

You cannot count every leaf on a tree, so you count a sample and scale it. The calculator does this in three steps, which are our own working: the area density is the number of leaves on the plate divided by the area of the plate; the leaves beneath the crown are the density times the area beneath the crown; and the total is the leaf area index times the leaves beneath the crown.

The plate

Hold a plate, a ring or a hoop of known size under a branch and count the leaves that cover it in one layer, with no gaps and no overlap. The example below uses a plate with a diameter of 10 inches. The plate and the crown are treated as circles, so each area is pi times the square of half the diameter. That formula is our own working.

The crown

The crown diameter is the width of the ground area under the branches, as you would see it in the tree's shadow at noon. For a tree that is not round, measure the width in several directions and average them. The tool turns the width into a circle. If you choose US units, the plate is in inches and the crown in feet; the tool converts the crown to inches before it divides, so the units match.

Leaf area index

The Thünen Institute defines the leaf area index as the area of leaves and needles per unit of ground area [1]. Wikipedia adds that the index ranges from 0 for bare ground to over 10 for dense conifer forests [2]. The default of 4.7 and the typical range of 4 to 8 for deciduous trees are our own planning values, not figures from a source we could cite. If you leave the box blank, the tool uses 4.7. A thick, shady crown has a higher index than a sparse one.

A worked example

Take a plate with a diameter of 10 inches, covered by 8 leaves plus gaps, which we round to 9, and a crown 30 feet wide. The plate has an area of 78.54 square inches, so the density is 0.11459 leaves per square inch. The crown has 101,788 square inches, which gives 11,664 leaves beneath it. Multiply by 4.7 to get 54,821 leaves, or about 55 thousand.

Why the result is only roughly 50 thousand

The result is best read as about 50 thousand. With 9 leaves our result is 54,821, about 10 percent above 50,000. With 8 leaves it would be 48,730. Both round to about 50 thousand, so a small change in the sample count moves the answer only a little. The calculator shows the rounded figure, 54,800, and the unrounded count so that you can see both.

Using metric units

With metric units, the plate diameter is in centimetres and the crown diameter in metres. The tool multiplies the crown by 100 to get centimetres, and works in square centimetres. A plate of 25.4 centimetres and a crown of 9.144 metres are the same as the example in inches and feet, and give the same 54,821 leaves. The crown area is shown in square metres, which is easier to picture.

Counting leaves on the plate

The count matters most, because the result is proportional to it. Count only one layer, and do not count leaves that overlap others. If there are gaps, estimate how many leaves would fill them, as in the example above, where 8 leaves and some gaps become 9. Repeat the count under three or four branches, in sun and in shade, and use the average. A better sample gives a better result.

An order-of-magnitude estimate

We treat the result as an answer of the order of tens of thousands: the first digit or two is useful, the later ones are not. The example crown, 30 feet wide, gives tens of thousands of leaves, and that scale is what the estimate tells you. The result is not a count, and two people counting the same tree could differ noticeably.

Leaf area index by species

The tool has no table of leaf area index by species, because we found no published table to cite. You can type your own index if you have a figure for your species from a forestry source. The method counts flat leaves on a plate, so it suits broadleaf trees such as maples, oaks and birches better than needle-bearing ones. That last point is our own caution.

Common mistakes

  • Counting leaves that overlap. Count one layer only.
  • Mixing the units. Keep the plate in inches or centimetres and the crown in feet or metres, as the labels say.
  • Measuring the crown at the branch tips of one side. Use the width of the whole shadow.
  • Trusting the digits. The result is good to the first one or two figures at best.

What next

Use this often? Add Tree Leaves to your Home screen.

Frequently asked questions

What is a tree leaves calculator?

A tool that estimates the total number of leaves on a tree from a sample count, the crown width and a leaf area index.

How many leaves does a tree have?

It depends on the species and size. For example, a crown 30 feet wide with the default index gives about 55 thousand.

What is the leaf area index?

The area of leaves and needles per unit of ground area. The tool uses 4.7 by default and treats 4 to 8 as a typical range for deciduous trees; both are planning values.

How accurate is the tree leaves calculator?

It is an order-of-magnitude estimate. It depends on a good sample count and a round crown.

What size of plate should I use?

Any size that you can lay under a branch, with its diameter known. The example uses 10 inches.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools