A torsional constant calculator finds the torsion constant J of a cross-section, the property that decides how much a bar twists under a torque. It also gives the polar moment of area, so it covers the polar moment calculator too. Pick a circle, tube, ellipse, rectangle or square and enter its size.
How to use the torsional constant calculator
- Choose US or metric units.
- Pick the cross-section.
- Enter its dimensions.
- Press Calculate.
What the constant does
When a bar is twisted by a torque, the angle of twist depends on its torsion constant J, and on the material and the length. For a circular section, the polar moment of inertia and the torsion constant are the same, and the twist is φ = T L ÷ (J G) [1]. For non-circular sections the torsion constant generally differs from the polar moment, because twisting is accompanied by warping and cross-sections do not stay plane [3].
Circles and tubes
For a solid circle, J = π R⁴ ÷ 2 = π D⁴ ÷ 32 [1], and for a hollow circle J = π (D⁴ − d⁴) ÷ 32 [2]. For a solid circle of 5 centimetres, J is about 61.36 cm⁴. Enter 50 millimetres in metric mode and the tool gives 61.359 cm⁴, or 613,590 mm⁴.
Ellipse
For an ellipse with semi-axes a and b, the torsion constant is K = π a³ b³ ÷ (a² + b²), where a and b are the major and minor radius [1]. The tool asks for the full width and height and halves them. For axes of 8 and 4 centimetres, the tool gives 80.425 for J in cm⁴, which is the value for semi-axes of 4 and 2.
Rectangle
The solid rectangle is K = a b³ ÷ 3 − 0.21 b⁴ + 0.0175 b⁸ ÷ a⁴, where a is the long side and b the short one. It is the approximation J ≈ a b³ (16/3 − 3.36 (b/a)(1 − b⁴/(12 a⁴))) with a and b as half-lengths, which has an error of not more than 4 percent [1]. For 10 by 5, the formula gives 286.1.
Square
For a solid square of side s, K = 9 s⁴ ÷ 64. This follows from J ≈ 2.25 a⁴ with a as half the side [1], since a half side of s ÷ 2 gives 2.25 s⁴ ÷ 16 = 9 s⁴ ÷ 64. A side of 5 cm gives 87.89 cm⁴, and the tool gives the same for 50 millimetres.
Thin-walled tube
For a thin-walled closed tube, the Bredt approximation is J ≈ 4 Aₘ² ÷ ∮(ds ÷ t), where Aₘ is the area enclosed by the wall mid-line and t the local thickness [3]. This tool uses one thickness t for all four walls of a rectangular tube with outer sides a and b, so the mid-line is (a − t) by (b − t), which reduces to K = 2 t (a − t)² (b − t)² ÷ (a + b − 2t). That reduction is our own working. For a 50 by 30 mm tube with 3 mm walls it gives 13.057 cm⁴.
Polar moment of area
The polar moment J = Ix + Iy comes from the perpendicular axis theorem [2], and for a circle it equals the torsion constant. For the other shapes, the tool gives it from the textbook second moments: rectangle a b (a² + b²) ÷ 12, square a⁴ ÷ 6 and ellipse π a b (a² + b²) ÷ 4. These shape formulas are our own working. They are larger than the torsion constant and are not used for twist.
US and metric
Pick US to enter dimensions in inches, or metric to enter millimetres. The result is shown in mm⁴, cm⁴ and in⁴, whatever you choose, and the length factor is 25.4 mm per inch. Remember that the dimension is raised to the fourth power, so a small error in the diameter makes a large error in J: a 10 percent error in diameter gives about 46 percent in J.
Limits
The formula for the rectangle is accurate to about 4 percent [1]. This tool leaves out I-sections and hollow ellipses. Real members have fillets, holes and end restraints. Use the results for a first estimate only, and check structural parts with an engineer.
Using the results
Pick the shape, enter the dimensions, and press Calculate. Compare a solid circle of 50 mm with a hollow one of 50 mm outside and 40 mm inside to see that most of the stiffness stays when the core is removed. Compare a square and a circle of equal area, to see that the circle is stiffer in torsion. Then use J in the twist formula with the length and the shear modulus.
Stiffness and the fourth power
Because the diameter enters to the fourth power, doubling the diameter of a round shaft makes J sixteen times larger, from J = π D⁴ ÷ 32 [2]. Doubling the thickness of a thin rectangle raises J by about eight times, since the leading term is a b³ ÷ 3 [1]. This is why a thick, round or closed section resists twisting so much better than a thin, open one. These comparisons are our own arithmetic.
A twist example
Use the solid 50 millimetre circle from above, with J = 61.359 cm⁴, which is 6.1359 × 10⁻⁷ m⁴. For a circular section, the twist is φ = T L ÷ (J G) [1]. As our own example, take a torque of 100 newton metres, a length of 1 metre and a shear modulus of 80 gigapascals. The shear modulus is an assumed value for illustration, so use your own material data.
Then J G = 6.1359 × 10⁻⁷ × 80 × 10⁹ = 49,087 newton metres squared, and φ = 100 × 1 ÷ 49,087 = 0.00204 radians, or about 0.117 degrees. Doubling the length doubles the twist, while a bar made of the same material with half the diameter twists sixteen times as much.
Common mistakes
- Using the polar moment of a rectangle for twist. Use the torsion constant.
- Entering radius instead of diameter. The boxes take diameters.
- Mixing inches and millimetres. Pick one unit system.
- Using a thick wall for the thin-walled formula. The wall must be thin.
What next
Use this often? Add Torsional Co to your Home screen.
Frequently asked questions
What is a torsional constant calculator?
A tool that finds the torsion constant of a cross-section, used for the angle of twist, along with the polar moment of area.
What is the polar moment of a solid circle?
J = π D⁴ ÷ 32, where D is the diameter.
What is the polar moment of a hollow circle?
J = π (D⁴ − d⁴) ÷ 32, with D the outer and d the inner diameter.
Is the torsion constant the same as the polar moment?
Only for circular sections. For other shapes the torsion constant is smaller.
How accurate is the rectangle formula?
About 4 percent for the approximate rectangle formula, as stated in the Wikipedia article on the torsion constant.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.